Highly Efficient and Robust Full-Color Organic Afterglow through 2D Superlattices Embedment.

Adv Mater

State Key Laboratory of Organic Electronics and Information Displays & Institute of Advanced Materials (IAM), Jiangsu National Synergistic Innovation Center for Advanced Materials (SICAM), Nanjing University of Posts & Telecommunications, 9 Wenyuan Road, Nanjing, 210023, China.

Published: November 2022

Purely organic afterglow (POA) originating from the slow radiative decay of stabilized triplet excited states has shown amazing potential in many fields. However, achieving highly stable POA with high phosphorescent quantum yield (PhQY) and long lifetime is still a formidable challenge owing to the intrinsically active and sensitive nature of triplet excitons. Here, triplet excitons of phosphors are protected and stabilized by embedding in tricomponent trihapto self-assembled 2D hydrogen-bonded superlattices, which not only enables deep-blue POA with high PhQY (up to 65%), ultralong lifetime (over 1300 ms) and the highest figure-of-merit at room temperature, but also achieves excellent stability capable of resisting quenching effects of oxygen, solvent, pressure, light, and heat. In addition, the POA color is tuned from deep-blue to red via efficient Förster resonance energy transfer from the deep-blue POA emitters to the fluorophores. Moreover, with the high-performance, robust, and full-color POA materials, flexible anti-counterfeit displays and direct-current (DC)-driven lifetime-encrypted color Morse Code applications are facilely realized.

Download full-text PDF

Source
http://dx.doi.org/10.1002/adma.202206712DOI Listing

Publication Analysis

Top Keywords

robust full-color
8
organic afterglow
8
poa high
8
triplet excitons
8
deep-blue poa
8
poa
6
highly efficient
4
efficient robust
4
full-color organic
4
afterglow superlattices
4

Similar Publications

Robust low threshold full-color upconversion lasing in rare-earth activated nanocrystal-in-glass microcavity.

Light Sci Appl

January 2025

State Key Laboratory of Luminescent Materials and Devices, and Guangdong Provincial Key Laboratory of Fiber Laser Materials and Applied Techniques, School of Materials Science and Engineering, South China University of Technology, 510640, Guangzhou, China.

Visible light microlasers are essential building blocks for integrated photonics. However, achieving low-threshold (μW), continuous-wave (CW) visible light lasing at room temperature (RT) has been a challenge because of the formidable requirement of population inversion at short wavelengths. Rare-earth (RE)-activated microcavities, featuring high-quality factor (Q) and small mode volume of whispering gallery modes, offer a great opportunity for achieving infrared-to-visible upconversion (UC) lasing.

View Article and Find Full Text PDF

Exploring ionogels with superior conductivity, mechanical properties, and long-lasting room temperature phosphorescence (RTP) offers considerable potential for new-generation optoelectronics. However, reports on ionogels remain limited owing to the contradiction between the flexibility required for stretching and the rigidity necessary for RTP and load-bearing within the same ionogels. Here, a facile strategy is reported to enhance the toughness and extend the RTP of ionogels by salting-out-induced microphase separation, which results in the formation of an IL-rich phase (soft) for stretching and ionic conduction and a polymer-rich phase (stiff) for energy dissipation and clustering-triggered phosphorescence.

View Article and Find Full Text PDF

Monolithic Integration of Full-Color Microdisplay Screen with Sub-5 µm Quantum-Dot Pixels.

Adv Mater

November 2024

Hunan Institute of Optoelectronic Integration, College of Materials Science and Engineering, Hunan University, Changsha, 410082, P. R. China.

Monolithic integration of color-conversion materials onto blue-backlight micro-light-emitting-diodes (micro-LEDs) has emerged as a promising strategy for achieving full-color microdisplay devices. However, this approach still encounters challenges such as the blue-backlight leakage and the poor fabrication yield rate due to unsatisfied quantum dot (QD) material and fabrication process. Here, the monolithic integration of 0.

View Article and Find Full Text PDF

Electrohydrodynamic Inkjet Printing of Three-Dimensional Perovskite Nanocrystal Arrays for Full-Color Micro-LED Displays.

ACS Appl Mater Interfaces

May 2024

Department of Electronic Science, Fujian Engineering Research Center for Solid-State Lighting, Xiamen University, Xiamen 361005, Fujian, China.

Article Synopsis
  • Perovskite nanocrystal (PeNC) arrays are gaining attention for micro-LED displays due to their narrow emission properties and customizable color output.
  • Electrohydrodynamic (EHD) inkjet printing is highlighted as an effective method for creating PeNC arrays, but challenges remain in producing stable and bright red light-emitting CsPbBrI nanocrystal arrays.
  • This study introduces a novel red PeNC colloidal ink that combines PeNCs, polystyrene, and xylene solvent to enhance brightness, stability, and shape control for 3D PeNC array fabrication, demonstrating a high-resolution printing capability suitable for micro-LED displays.
View Article and Find Full Text PDF

Light-element-based fluorescent materials, colloidal graphene quantum dots, and carbon dots (CDs) have sparked an immense amount of scientific interest in the past decade. However, a significant challenge in practical applications has emerged concerning the development of solid-state fluorescence (SSF) materials. This study addresses this knowledge gap by exploring the unexplored photonic facets of C-based solid-state microphotonic emitters.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!