The influence of microstructure of silica-enhanced cement on the mechanical performance of cement is difficult to describe. In this study, we used the scanning electron microscope and image processing method to investigate the relationship between the complicity of cement microstructure and compressive strength under various temperatures and curing times. Fractal dimension was applied to describe the complicity of silica-enhanced cement. The relationships among compressive strength, fractal dimension, temperature, curing time and pore structure of cement were identified. The results show that curing time directly controls the complicity of microstructure of silica-enhanced cement and compressive strength by altering the pore orientation and macropore ratio in silica-enhanced cement. The curing temperature affects the complicity of cement microstructure and compressive strength indirectly by changing the ratio of micropore and small pore. The fractal dimension of silica-enhanced cement shows good correlation with compressive strength. Pore size distribution is the most important factor that influences the complicity of cement matrix and compressive strength of silica-enhanced cement. When building up the macroscopic mechanical performance model of silica-enhanced cement, we should consider the influence of pore size distribution in cement under different curing temperatures and times on the complicity of cement microstructure.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9363988 | PMC |
| http://dx.doi.org/10.1098/rsos.220150 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Temperature dynamics and mechanical properties analysis of carbon fiber epoxy composites radiated by nuclear explosion simulated light source.
Sci Rep
January 2025
Engineering Research Center of Flexible Radiation Protection Technology, Universities of Shaanxi Province, Xi'an Polytechnic University, Xi'an, 710048, Shaanxi, China.
The impact of light radiation, a predominant energy release mechanism in nuclear explosions, on material properties is of critical importance. This investigation employed an artificial light source to replicate the effects of nuclear explosion radiation and utilized a physical information neural network (PINN) to examine the temperature evolution and corresponding changes in the mechanical properties of carbon fiber/epoxy composites (CFEC). A light source simulating nuclear explosion's light radiation was built to irradiate the CFEC, then measure the reflection spectrum and temperature of samples.
View Article and Find Full Text PDFInvestigating slope stability of multiple stopes prone to instability in the Ziluoyi iron ore mining site.
Sci Rep
January 2025
School of Safety Engineering, China University of Mining and Technology, Xuzhou, 221116, China.
The ore mining sites commonly experience slope instability, which is causing concern for the workers' safety and the operation's stability. Considering the Ziluoyi iron ore mining site as a case study, uniaxial compression strength and shear tests are performed on the lower disk peripheral rock, ore body, and upper disk peripheral rock, leading to the extraction of compressive strength and elastic modulus (lower disk: 77.7 MPa-9.
View Article and Find Full Text PDFDamage constitutive model and mechanical properties of a concrete limestone composite after acid corrosion.
Sci Rep
January 2025
College of Civil Engineering, Guizhou University, Huaxi District, Guiyang, 550025, Guizhou, China.
Long-term erosion by acidic solutions in karst regions leads to continuous deterioration of the physical and mechanical properties at the interfaces of engineering structures, adversely affecting their operational performance. To investigate the degradation patterns of the mechanical properties and corrosion mechanisms of the concrete‒limestone composite (CLC) after exposure to acidic corrosion, three kinds of CLC samples treated with acidic solutions of different pH values were fabricated. Mechanical property analysis was conducted via triaxial compression testing methods.
View Article and Find Full Text PDF3D printing of different fibres towards HA/PCL scaffolding induces macrophage polarization and promotes osteogenic differentiation of BMSCs.
PLoS One
January 2025
Department of Orthopaedic Surgery, The Second Affiliated Hospital of Zunyi Medical University, Zunyi, Honghuagang District, Guizhou, China.
With the rise of bone tissue engineering (BET), 3D-printed HA/PCL scaffolds for bone defect repair have been extensively studied. However, little research has been conducted on the differences in osteogenic induction and regulation of macrophage (MPs) polarisation properties of HA/PCL scaffolds with different fibre orientations. Here, we applied 3D printing technology to prepare three sets of HA/PCL scaffolds with different fibre orientations (0-90, 0-90-135, and 0-90-45) to study the differences in physicochemical properties and to investigate the response effects of MPs and bone marrow mesenchymal stem cells (BMSCs) on scaffolds with different fibre orientations.
View Article and Find Full Text PDFEnhanced bone cement for fixation of prosthetic joint utilizing nanoparticles.
J Mater Sci Mater Med
January 2025
Biomedical Engineering Department, Faculty of Engineering, Helwan University, Cairo, Egypt.
Bone cement is commonly utilized to secure prosthetic joints in the body because of its robust fixation, stability, biocompatibility, and immediate load-bearing capability. However, issues such as loosening, leakage, and insufficient bioactivity can lead to its failure. Therefore, improving its mechanical, physical, and biological properties is crucial for enhancing its efficiency.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!