Broadband near-infrared (NIR) phosphors are necessary materials for developing portable NIR light sources. Moreover, exploiting an NIR phosphor with a main peak located beyond a wavelength of 900 nm remains a challenge because this spectral range has great potential in biological nondestructive testing and solution testing. In this study, a range of Cr-doped ZnTaO (ZTO) phosphors were completely synthesized by a solid-state method, which show broadband Cr emission centered at 935 nm with a large full width at half maximum (FWHM) of 185 nm due to two distorted octahedral sites. A packaged phosphor-converted light-emitting diode (pc-LED) device is used to penetrate a 5-cm-thick chicken breast and identify diverse solutions based on differences in the measured transmission spectra. The results indicate broad application prospects in the field of biological tissue penetration and solution analysis.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1021/acs.inorgchem.2c01403 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Non-destructive prediction and pixel-level visualization of polysaccharide-based properties in ancient paper using SWNIR hyperspectral imaging and machine learning.
Carbohydr Polym
March 2025
Plant Fiber Material Science Research Center, State Key Laboratory of Pulp and Paper Engineering, School of Light Industry and Engineering, South China University of Technology, Guangzhou 510640, China; Guangdong Provincial Key Laboratory of Plant Resources Biorefinery, No. 100, West Outer Ring Road, Guangzhou University Town, Panyu District, Guangzhou 510006, China.
Ancient documents and artworks are invaluable cultural heritage artworks that require careful preservation. Traditional methods for assessing their physical and chemical properties-such as tearing index, tensile index, water absorption, and pH-are often destructive, risking irreversible damage. This study introduces a novel, non-destructive approach using Short-Wave Near-Infrared (SWNIR) hyperspectral imaging (HSI) combined with advanced machine learning models.
View Article and Find Full Text PDFMiniaturized Wearable Biosensors for Continuous Health Monitoring Fabricated Using the Femtosecond Laser-Induced Graphene Surface and Encapsulated Traces and Electrodes.
ACS Sens
January 2025
Department of Electrical and Computer Engineering, Missouri University of Science and Technology, Rolla, Missouri 65409, United States.
Wearable sensors are increasingly being used as biosensors for health monitoring. Current wearable devices are large, heavy, invasive, skin irritants, or not continuous. Miniaturization was chosen to address these issues, using a femtosecond laser-conversion technique to fabricate miniaturized laser-induced graphene (LIG) sensor arrays on and encapsulated within a polyimide substrate.
View Article and Find Full Text PDFIntegrated GWAS, BSA-seq, and RNA-seq analyses to identify candidate genes associated with male fertility trait in peach.
Plant Physiol Biochem
January 2025
National Key Laboratory for Germplasm Innovation & Utilization of Horticultural Crops, Zhengzhou Fruit Research Institute, Chinese Academy of Agricultural Sciences, Zhengzhou, 450009, China; Zhongyuan Research Center, Chinese Academy of Agricultural Sciences, Xinxiang, 453500, China. Electronic address:
Male sterility in peach (Prunus persica L.), characterized by the absence of fertile pollen grains in the anther, is determined by a recessive allele in homozygosis of the major gene located on chromosome 6. Developing tightly linked molecular markers can help identify appropriate peach parents or male-sterile plants for early culling in segregating progenies, thereby increasing breeding efficiency.
View Article and Find Full Text PDFEnhancing structural health monitoring of fiber-reinforced polymer composites using piezoresistive TiCT MXene fibers.
Sci Rep
January 2025
Department of Materials Science and Engineering, Faculty of Engineering, Çanakkale Onsekiz Mart Universitesi, 17100, Çanakkale, Turkey.
The anisotropic behavior of fiber-reinforced polymer composites, coupled with their susceptibility to various failure modes, poses challenges for their structural health monitoring (SHM) during service life. To address this, non-destructive testing techniques have been employed, but they often suffer from drawbacks such as high costs and suboptimal resolutions. Moreover, routine inspections fail to disclose incidents or failures occurring between successive assessments.
View Article and Find Full Text PDFNondestructive Mechanical Characterization of Bioengineered Tissues by Digital Holography.
ACS Biomater Sci Eng
January 2025
Mechanical Engineering Department, Worcester Polytechnic Institute, Worcester, Massachusetts 01609, United States.
Mechanical properties of engineered connective tissues are critical for their success, yet modern sensors that measure physical qualities of tissues for quality control are invasive and destructive. The goal of this work was to develop a noncontact, nondestructive method to measure mechanical attributes of engineered skin substitutes during production without disturbing the sterile culture packaging. We optimized a digital holographic vibrometry (DHV) system to measure the mechanical behavior of Apligraf living cellular skin substitute through the clear packaging in multiple conditions: resting on solid agar as when the tissue is shipped, on liquid media in which it is grown, and freely suspended in air as occurs when the media is removed for feeding.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!