Purpose: To investigate the risk factors related to failure of removable partial dentures (RPDs) and to compare the survival of RPDs when abutment teeth have good vs reduced bone support.
Materials And Methods: In this longitudinal patient record-based cohort study with a mean follow-up of 44.9 months, Cox regression models were used to evaluate the associations between clinical covariates and abutment tooth failure, as well as prosthesis failure.
Results: A total of 142 patients and 172 RPDs were included. Of the 172 prostheses, 64 (nearly 40%) failed after a mean time of about 4 years. Loss of abutment teeth was the main reason leading to RPD failure, followed closely by poor fit and adaptation. No factor was shown to be statistically significant at the prosthesis level. Women (Hazard Ratio [HR] = 0.542), endodontic treatment (HR = 3.460), presence of post and core (HR = 0.302), presence of a prosthetic crown (HR = 3.403), and abutment tooth type (in relation to incisor: canine HR = 0.196, premolar HR = 0.449) were the risk factors statistically significantly associated with the loss of abutment teeth. The pre-prosthesis amount of bone support of the teeth did not affect their prognosis as abutments for RPDs.
Conclusion: RPD treatment modality presented a high failure rate after a mean follow-up of 4 years. Vital abutment teeth had a better survival rate than the ones treated endodontically (whether restored with or without a post and core); nevertheless, the amount of bone support did not affect their survival.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.11607/ijp.7457 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Micro CT evaluation of marginal discrepancies of endocrown restored molars with different intrapulpal depths and materials of fabrication. (in-vitro study).
BMC Oral Health
January 2025
Faculty of dentistry, Ain Shams University, Cairo, Egypt.
Objective: The purpose of this study was to evaluate the effect of different preparation depths (0, 2 and 4 mm) of different restoration designs (classic endocrown design versus overlay design) on marginal adaptation of restorations fabricated of two different restorative materials (lithium disilicate and PEEK).
Materials And Methods: Sixty mandibular natural molars were collected as abutments for the restorations of this study, and grouped in three main groups of different cavity depths (0, 2 and 4). Each group was divided into two subgroups according to material of fabrication to (L) for lithium disilicate (IPS emax CAD, Ivoclar vivadent, Switzarland) and (P) for PEEK (Bio-hpp, Bredent, Germany).
Evaluation of stress patterns in teeth with endodontic treatment and periapical lesions as abutments for fixed prosthesis: a finite element analysis study.
BMC Oral Health
January 2025
Department of Agr. Machinery and Technology Engineering, Akdeniz University, Antalya, Turkey.
Background: Examining stress distributions in abutment teeth with periapical lesions is essential for understanding their biomechanical impact on dental structures and tissues. This study uses finite element analysis (FEA) to evaluate these stress patterns under occlusal forces, aiming to enhance treatment strategies and prosthetic designs.
Methods: Three FEA models were created: a healthy mandibular premolar (Model 1), a premolar with a single crown and a lesion repaired using a fiber-post (Model 2), and 3) a premolar with a lesion repaired using fiber-post to support a four-member bridge (Model 3).
[Influence of emergence profile designs on the peri-implant tissue in the mandibular molar: A randomized controlled trial].
Beijing Da Xue Xue Bao Yi Xue Ban
February 2025
Fourth Clinical Division, Peking University School and Hospital of Stomatology & National Center of Stomatology & National Clinical Research Center for Oral Diseases & National Engineering Research Center of Oral Biomaterials and Digital Medical Devices & Beijing Key Laboratory of Digital Stomatology, Beijing 100081, China.
Objective: To compare the influence of different emergence profile of implants in mandibular molar on the peri-implant soft tissue.
Methods: Forty-four implants were divided into two equal groups by mucosal thickness, ≥2 mm (group A) or < 2 mm (group B), and were randomly included in the test group and the control group. In the control group, the patients were treated by a prosthesis with no transmucosal modifications (subgroups A1 and B1).
Thermal stress behavior of monolithic zirconia crowns with different thicknesses.
J Prosthodont Res
January 2025
Advanced Prosthodontics, Oral Health Sciences, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, Tokyo, Japan.
Purpose: This study was aimed at investigating the thermal stresses in monolithic zirconia crowns (MZC) of various thicknesses and elucidating their thermal behavior under cooling or heating changes in the oral cavity. Additionally, the clinical availability and potential issues of MZC were examined by comparing them with other crown materials.
Methods: Finite element models comprising MZC (0.
The influence of prosthetic treatments and implant-supported prostheses on posterior mandibular ridge atrophy: a retrospective cohort study.
BMC Oral Health
January 2025
Division of Restorative Dentistry, Periodontology and Prosthodontics, Department of Dental Medicine and Oral Health, Medical University of Graz, Billrothgasse 4, Graz, 8010, Austria.
Aims: Bone preservation is a requirement for long-term stability of dental prostheses, which is all the more important in the posterior mandible, given the particular challenges these areas pose to prosthetic treatment. The objective was to investigate the implications of different prostheses on the atrophy of posterior alveolar bone after tooth loss.
Materials And Methods: A total of 457 treatment cases were retrieved from the medical documentation and information network.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!