Effect of Sunlight on the Change in Color of Unsteamed and Steamed Beech Wood with Water Steam.

Polymers (Basel)

Faculty of Wood Sciences and Technology, Technical University in Zvolen, T.G. Masaryka 24, 96001 Zvolen, Slovakia.

Published: April 2022

This paper presents the differences in the color changes of unsteamed and steamed beech wood ( L.) caused by long-term exposure to sunlight on the surface of wood in interiors for 36 months. The light white-gray color of the yellow tinge of native beech wood darkened under the influence of sunlight, and the wood took on a pale brown color of yellow tinge. The degree of darkening and browning is quantified by the value of the total color difference ∆ = 13.0. The deep brown-red color of steamed beech under the influence of sunlight during the exposure brightened, and the surface of the wood took on a pale brown hue. The degree of lightening of the color of steamed beech wood in the color space CIE is quantified by the value of the total color difference ∆ = 7.1. A comparison of the color changes of unsteamed and steamed beech wood through the total color difference ∆ due to daylight shows that the surface of steamed beech wood shows 52.2% smaller changes than unsteamed beech wood. The lower value of the total color difference of steamed beech wood indicates the fact that steaming of beech wood with saturated water steam has a positive effect on the color stability and partial resistance of steamed beech wood to the initiation of photochemical reactions induced by UV-VIS wavelengths of solar radiation. Spectra ATR-FTIR analyses declare the influence of UV-VIS components of solar radiation on unsteamed and steamed beech wood and confirm the higher color stability of steamed beech wood.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9104894PMC
http://dx.doi.org/10.3390/polym14091697DOI Listing

Publication Analysis

Top Keywords

beech wood
48
steamed beech
40
unsteamed steamed
16
total color
16
color difference
16
wood
15
color
14
beech
13
changes unsteamed
12
difference ∆
12

Similar Publications

Acoustic, Mechanical, and Thermal Characterization of Polyvinyl Acetate (PVA)-Based Wood Composites Reinforced with Beech and Oak Wood Fibers.

Polymers (Basel)

January 2025

Research Laboratory for Sustainable Development and Health, Department of Applied Physics, Faculty of Sciences and Technics, Cadi Ayyad University, Marrakesh 40000, Morocco.

Considering the growing need for developing ecological materials, this study investigates the acoustic, mechanical, and thermal properties of wood composites reinforced with beech or oak wood fibres. Scanning electron microscopy (SEM) revealed a complex network of interconnected pores within the composite materials, with varying pore sizes contributing to the material's overall properties. Acoustic characterization was conducted using a two-microphone impedance tube.

View Article and Find Full Text PDF

The present paper investigates the possibility of replacing the traditional L-type corner joint used in chair construction with a 3D printed connector, manufactured using the Fused Filament Fabrication (FFF) method and black PLA as filament. The connector was designed to assemble the legs with seat rails and stretchers, and it was tested under diagonal tensile and compression loads. Its performance was compared to that of the traditional mortise-and-tenon joint.

View Article and Find Full Text PDF

Analyzing the Vibration Response of Adhesively Bonded Composite Cantilevers.

Materials (Basel)

December 2024

Division of Structural Mechanics and Material Mechanics, Faculty of Civil Engineering, Cracow University of Technology, 31-155 Kraków, Poland.

In this study, we investigated the vibration of adhesively bonded composite cantilevers consisting of two beech wood lamella and a bondline of flexible polyurethane. The beams had a constant total height, while the thickness of the adhesive layer varied. We analyzed both the driven and free vibration of a single cantilever beam and a cantilever with an additional mass attached to its end.

View Article and Find Full Text PDF

The surfaces of beech wood samples were treated with polyethylenimine (PEI) solutions at three different concentrations-0.5%, 1% and 2%-and two molecular weights-low molecular weight (LMW) and high molecular weight (HMW). The effects of PEI surface treatment of wood were characterized by FT-IR spectroscopy, the penetration depth of PEI (EPI fluorescence spectroscopy), the bonding position of PEI (by SEM), the wetting and surface energy, and the water uptake.

View Article and Find Full Text PDF

Oak wilt causes severe dieback of Quercus serrata, a dominant tree species in the lowlands across Japan. This study evaluated the effects of oak wilt on the wood-inhabiting fungal community and the decay rate of deadwood using a field monitoring experiment. We analysed the fungal metabarcoding community from 1200 wood samples obtained from 120 experimental logs from three forest sites at five different time points during the initial 1.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!