In the context of nosocomial infections, there is an urgent need to develop efficient nanomaterials (NMs) with antibacterial properties for the prevention of infection diseases. Metal oxide nanoparticles (MeO-NPs) are promising candidates for the development of new antibacterial textiles. However, the direct exposure to MeO-NPs and MeO-coated NMs through skin contact could constitute a severe hazard for human health. In this work, the toxicity of copper and zinc oxide (CuO, ZnO) NPs antimicrobial-coated textiles was assessed on an in vitro reconstructed 3D model of epidermis. Thus, MeO-NPs and extracts from MeO-coated NMs were tested on EpiDerm™ skin model according to OECD TG 431 (Corrosion Test) and 439 (Irritation Test), respectively. Skin surface fluids composition is a crucial aspect to be considered in the development of NMs that have to encounter this tissue. So, for the irritation test, coated textiles were extracted in artificial sweat solutions at pH 4.7 and 6.5. Skin tissue viability, pro-inflammatory interleukin-8 secretion and morphological alteration of intermediate and actin filaments of keratinocytes were evaluated after 18 h exposure to extracts from CuO- and ZnO-coated textiles. Analysis of extracts at the two pH conditions indicated that released ions and not NPs are involved in promoting adverse effects on epidermis. Since Cu and Zn ions are known to penetrate epidermis, Balb/3 T3 cells were used as model of dermis. Fibroblasts viability was investigated after the exposure to trans-epidermis permeated ions, collected from EpiDerm™ basal supernatants, and to extracts, as representative of a direct interaction of ions with dermis cells by wounded skin. From our data we can conclude that: 1) skin surface fluids composition is a key parameter for the stability of NPs-coated textiles; 2) MeO ions released from coated textiles can deeply affect the epidermal tissue and the underlying dermal cells upon trans-epidermal permeation; 3) skin barrier integrity is a fundamental prerequisite that should be taken into account during the assessment of NMs safety by direct contact exposure.

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.impact.2020.100282DOI Listing

Publication Analysis

Top Keywords

coated textiles
12
cuo zno
8
meo-coated nms
8
irritation test
8
skin surface
8
surface fluids
8
fluids composition
8
textiles
7
skin
7
nms
5

Similar Publications

Polyethylene terephthalate (PET) is a widely utilized synthetic polymer, favored in various applications for its desirable physicochemical characteristics and widespread accessibility. However, its extensive utilization, coupled with improper waste disposal, has led to the alarming pollution of the environment. Thus, recycling PET products is essential for diminishing global pollution and turning waste into meaningful materials.

View Article and Find Full Text PDF

An electrochromic alginate fiber based on a WO/PEDOT:PSS composite layer.

Int J Biol Macromol

January 2025

College of Chemistry and Chemical Engineering, State Key Laboratory of Bio-fibers and Eco-textiles, College of materials science and engineering, Shandong Collaborative Innovation Center of Marine Bio-based Fibers and Ecological Textiles, Qingdao University, Qingdao 266071, PR China.

In this experiment, we studied a technique that permits the continuous fabrication of electrochromic alginate fibers because there hasn't been much research on electrochromic alginate fibers. Therefore, it's important to investigate ways to increase the application areas of alginate fibers. AgNP‑calcium alginate fibers with high electrical conductivity were prepared by Ag substitution method.

View Article and Find Full Text PDF

Quaternized Nanofiber-Based Anion-Exchange Chromatography Membrane with Periodic Diagonal Surface Structure for Efficient Protein Separation.

ACS Appl Mater Interfaces

January 2025

Key Laboratory of Textile Fiber and Products, Ministry of Education, Hubei International Scientific and Technological Cooperation Base of Intelligent Textile Materials & Application, Wuhan Textile University, Wuhan 430200, China.

Constructing a nanofibrous membrane with high flow rate surface pore structure and high-density ligand chemical structure is a promising strategy to balance the trade-off between high flow rates and high adsorption capacity for protein separation and purification. Herein, a nanofiber-based ion-exchange chromatography membrane with a periodic diagonal surface structure and high ionic strength ligands was fabricated using dispersion cross-linking, wet coating, and template printing with a three-wire diagonal woven mesh. For this membrane, EVOH nanofibers were used as skeleton, glutaraldehyde (GA) as cross-linking agent, and quaternized chitosan (QCS) as binder and functional ligand.

View Article and Find Full Text PDF

Eco-Friendly Fire-Retardant Coating on Cotton Using Layer by Layer Deposition Technique.

Molecules

December 2024

College of Mechatronic Engineering, Changwon National University, Changwon 51140, Gyeongsangnam-do, Republic of Korea.

Fire hazards are an increasing concern in several high-tech industries of public importance, particularly where textile fabrics are used in abundance. In this study, a novel layer by layer deposition method was utilized to develop a fire-retardant coating on cotton fabric. The method involves a hybrid cationic solution consisting of chitosan and branched polyethyleneimine, while bentonite clay was used as the anionic species.

View Article and Find Full Text PDF

Tensile Behavior Assessment of Grid-Type CFRP Textile-Reinforced Mortar with Different Design Variables.

Materials (Basel)

December 2024

Construction Technology Research Center, Construction Division, Korea Conformity Laboratories, 199, Gasan Digital 1-ro, Geumcheon-gu, Seoul 08503, Republic of Korea.

This study investigates the tensile behavior of carbon-fiber-reinforced polymer (CFRP) and textile-reinforced mortar (TRM) under various design variables to enhance understanding and application in construction structures. TRM reinforced with CFRP grids is highly effective for strengthening existing structures due to its lightweight nature, durability, ease of installation, and corrosion resistance. The research aims to evaluate how design parameters such as the CFRP grid type, mortar matrix strength (influenced by the water-to-cement ratio), specimen length, and grid width affect TRM's mechanical properties.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!