This study aimed to evaluate the filler contents (FCs), flexural properties, depth of cure (DOC), wear resistance, and handling properties of different low-viscosity bulk-fill resin composites (LVBRCs) and to determine the correlations between the tested parameters. Six LVBRCs, Beautifil-Bulk (BBF), Bulk Base Hard (BBH), Bulk Base Medium (BBM), Filtek Bulk-Fill Flowable Restorative (FBF), G-ænial Bulk Injectable (GBI), and SDR flow+ Bulk-Fill Flowable (SDR) were used. The DOC and flexural property tests were conducted according to the ISO 4049 specifications. The flexural strength, elastic modulus, and resilience were determined in 12 specimens that were obtained from each of the 6 materials. Sliding-impact-wear testing was conducted by evaluating the wear facets of the specimens using a noncontact profilometer and by confocal laser scanning microscopy. The handling properties of the LVBRC was assessed via extrusion force and thread formation measurements. The DOC for the majority of the LVBRCs was approximately 4 mm. Although the FCs and mechanical properties were material dependent, some LVBRCs exhibited excellent flexural properties and wear resistance. The LVBRCs demonstrated a wide range of extrusion force and thread formation. Regarding the correlations between the tested parameters, extremely strong negative and positive correlations were observed for the DOC versus extrusion force, flexural strength versus elastic modulus, maximum depth versus volume loss, and maximum depth versus thread formation. In addition, strong correlations between FCs and DOC, resilience, wear resistance, and extrusion force were observed.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.2341/20-253-L | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Controlled ligation and elongation of uniformly truncated amyloid nanofibrils.
Nanoscale
January 2025
Department of Biotechnology and Bioinformatics, Korea University, Sejong 30019, Republic of Korea.
This study investigates the production and inter-fibril interactions of uniformly truncated amyloid nanofibrils. By varying extrusion cycles (0, 50, and 100) and using carbonate filters with 100 nm and 200 nm pore sizes, precise fibril length control was achieved. Atomic force microscopy (AFM) confirmed that the mean length of the truncated fibrils corresponded to the respective pore size as extrusion cycles increased.
View Article and Find Full Text PDFCombining antibacterial and wound healing features: Xanthan gum/guar gum 3D-printed scaffold tuned with hydroxypropyl-β-cyclodextrin/thymol and Zn.
Carbohydr Polym
March 2025
Departamento de Farmacología, Farmacia y Tecnología Farmacéutica, I+D Farma (GI-1645), Faculty of Pharmacy, Instituto de Materiales (iMATUS), and Health Research Institute of Santiago de Compostela (IDIS), Universidade de Santiago de Compostela, 15782 Santiago de Compostela, Spain. Electronic address:
Biofilm formation on biological and material surfaces represents a heavy health and economic burden for both patient and society. To contrast this phenomenon, medical devices combining antibacterial and pro-wound healing abilities are a promising strategy. In the present work, Xanthan gum/Guar gum (XG/GG)-based scaffolds were tuned with thymol and Zn to obtain wound dressings that combine antibacterial and antibiofilm properties and favour the healing process.
View Article and Find Full Text PDFMechanical Behavior of 3D-Printed Zig-Zag Honeycomb Structures Made of BASF Ultrafuse 316L.
Materials (Basel)
December 2024
Laboratory of Microstructure Studies and Mechanics of Materials (LEM3), Lorraine University, UMR CNRS 7239, 57078 Metz, France.
The aim of this study is to determine the mechanical behavior of 2D honeycomb cellular structures with deformation initiators subject to quasi-static compression testing. Two different loading directions were studied: in-plane (IP) and out-of-plane (OP). The deformation initiators sought to stabilize the mechanical response by decreasing the initial peak force in the case of OP loading.
View Article and Find Full Text PDFThe Amount of Orthodontic Force Reaching the Dental Pulp and Neuro-Vascular Bundle During Orthodontic Movements in the Intact Periodontium.
Medicina (Kaunas)
December 2024
Department of Cariology, Endodontics and Oral Pathology, School of Dental Medicine, University of Medicine and Pharmacy Iuliu Hatieganu, Str. Motilor 33, 400001 Cluj-Napoca, Romania.
: Most orthodontic forces are absorbed-dissipated before reaching the dental pulp and its neuro-vascular bundle (NVB); however, no data are available about their amounts. The objective of this study was to assess the amount of orthodontic force that reaches the dental pulp and its NVB during orthodontic movements in a healthy periodontium. : This study involved the second lower premolars of nine patients and 180 numerical simulations.
View Article and Find Full Text PDFMechanical characteristics of roll crushing of ore materials based on discrete element method.
Sci Rep
January 2025
School of Mechatronics Engineering, Henan University of Science and Technology, Luoyang, 471003, China.
The application of high-pressure grinding rolls (HPGR) for ore crushing is considered to be one of the effective ways to save energy and reduce emissions in the ore processing industry. The crushing effect is directly determined by the forces of ore material during roll crushing. However, the mechanical state of ore material in roll crushing and the effect of roll structure, process parameters, feed particle size, on the force during the crushing of ore material needs to be expanded.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!