Process sustainability of biocatalytic processes is significantly empowered with the use of continuous-flow technologies that offer high productivity, minimal wastes and low volumetric consumption. Combining microreactor design with 3D printing technology can broaden the engineering potentials. This work proposes a protocol to modify the surface of 3D-printed PLA scaffolds, based on chitosan deposition. Mimicking the concept of microplates, multi-well plates were designed to facilitate parameter testing. Immobilization of laccase from Trametes versicolor was successfully performed, while chitosan and cross-linker concentration and incubation time were optimized. Τhe developed protocol was applied for the continuous flow bioconversion of hydroxyyrosol, yielding a TTN of 438.6 × 10 for a total of 10 h continuous use. Also, a peristaltic flow pattern seemed to favor the system performance, reaching 95% bioconversion efficiency in a total of 1 h reaction time. The potential of the developed system was further evaluated for the biotransformation of different biophenols from dietary sources, proving the efficiency of the system as a versatile biotechnological tool.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.jbiotec.2022.04.005 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Structurally sophisticated 3D-printed PCL-fibrin hydrogel meniscal scaffold promotes in situ regeneration in the rabbit knee meniscus.
Mater Today Bio
February 2025
Department of Orthopedics, the Fourth Medical Center of PLA General Hospital, Beijing, 100048, PR China.
A meniscus injury is a common cartilage disease of the knee joint. Despite the availability of various methods for the treatment of meniscal injuries, the poor regenerative capacity of the meniscus often necessitates resection, leading to the accelerated progression of osteoarthritis. Advances in tissue engineering have introduced meniscal tissue engineering as a potential treatment option.
View Article and Find Full Text PDFHarnessing machine learning algorithms for the prediction and optimization of various properties of polylactic acid in biomedical use: a comprehensive review.
Biomed Mater
January 2025
Department of Applied Mechanics, IIT Madras, Chennai-600036, Chennai, Tamil Nadu, 600036, INDIA.
Machine learning (ML) has emerged as a transformative tool in various industries, driving advancements in key tasks like classification, regression, and clustering. In the field of chemical engineering, particularly in the creation of biomedical devices, personalization is essential for ensuring successful patient recovery and rehabilitation. Polylactic acid (PLA) is a material with promising potential for applications like tissue engineering, orthopedic implants, drug delivery systems, and cardiovascular stents due to its biocompatibility and biodegradability.
View Article and Find Full Text PDFAdditively manufactured ready-to-use platform using conductive recycled PLA for ketamine sensing.
Mikrochim Acta
January 2025
Federal University of Uberlândia, Chemistry Institute, Uberlândia, MG, 38400-902, Brazil.
The use of 3D-printed electrodes is reported fabricated from in-house conductive filament composed of a mixture of recycled poly (lactic acid) (rPLA), graphite (Gpt), and carbon black (CB) for fast detection of the abused drug ketamine. Firstly, the performance of these electrodes was evaluated in comparison to 3D-printed electrodes produced employing a commercially available conductive filament. After a simple pretreatment step (mechanical polishing), the new 3D-printed electrodes presented better performance than the electrodes produced from commercial filament in relation to peak-to-peak separation of the redox probe [Fe(CN)]/ (130 mV and 759 mV, respectively), charge transfer resistance (R = 1.
View Article and Find Full Text PDFThe Influence of Polylactic Acid Filament Moisture Content on Dust Emissions in 3D Printing Process.
Sensors (Basel)
December 2024
Faculty of Computer Science, Kazimierz Wielki University, Chodkiewicza 30, 85-064 Bydgoszcz, Poland.
This paper presents the results of a study on the effect of moisture content in polylactic acid (PLA) filaments on dust emissions during incremental manufacturing. The tests were conducted in a customised chamber using a standard 3D printer, and Plantower PMS3003 sensors were used to monitor air quality by measuring PM1, PM2.5 and PM10 concentrations.
View Article and Find Full Text PDFMechanical Property Characterization of Virgin and Recycled PLA Blends in Single-Screw Filament Extrusion for 3D Printing.
Polymers (Basel)
December 2024
Department of Mechanical & Industrial Engineering, Rochester Institute of Technology, Dubai 341055, United Arab Emirates.
Additive manufacturing is an attractive technology due to its versatility in producing parts with diverse properties from a single material. However, the process often generates plastic waste, particularly from failed prints, making sustainability a growing concern. Recycling this waste material presents a potential solution for reducing environmental impact while creating new, functional parts.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!