The purpose of this study was to review our institution's experience using helmet molding therapy in children with isolated non-syndromic sagittal craniosynostosis before placement of cranial springs and provide objective measurements of craniometric changes to help determine its role in treatment.Patients who underwent preoperative helmet molding therapy for sagittal craniosynostosis were retrospectively reviewed. Three-dimensional surface tomography scans were used to measure head circumference, cranial width, cranial length, cranial index (CI), and cranial vault asymmetry.Seventeen patients underwent orthotic helmeting therapy before spring mediated cranial vault expansion. Patients spent a median of 48 days (interquartile range [IQR] 32, 57) in preoperative orthotic helmeting therapy. There were increases in both cranial width and length post-helmeting (median: 107.5 mm [IQR 104.8, 110.4] versus 115.6 mm [IQR 114.5, 119.3]; P < 0.001) (median: 152.8 mm [IQR 149.2, 154.9] versus 156.8 mm [IQR 155.0, 161.5]; P < 0.001), respectively. There was a greater increase in cranial width (P = 0.015). Consequently, patients' CI improved after preoperative helmeting (median: 0.702 [IQR 0.693, 0.717] versus 0.739 [0.711, 0.752]; P < 0.001). There was no evidence of growth restriction from helmeting (pre-helmeting Head circumference [HC]: median 96.8 percentile [IQR 90.6, 99.9] versus post-helmeting HC: 98.7 percentile [IQR 94.7, 99.8]; P = 0.109).Preoperative helmeting in patients with non-syndromic isolated sagittal craniosynostosis can be used to improve CI before surgical correction. Significant benefits can be achieved in shorter preoperative helmeting durations than previously reported with no evidence of cranial growth restriction, which supports its feasibility and utility in children undergoing spring mediated cranial vault expansion.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1097/SCS.0000000000008251 | DOI Listing |
J Craniofac Surg
January 2025
Department of Neurosurgery, Aichi Children's Health and Medical Center, Obu, Aichi, Japan.
Craniosynostosis limits normal cranial growth, significantly affecting the growth and development of children. This increase in intracranial pressure results in significant cosmetic and functional losses. This study investigated the efficacy of combining molding helmets with suturectomy for craniosynostosis.
View Article and Find Full Text PDFChilds Nerv Syst
December 2024
Hospital Zambrano Hellion, San Pedro Garza García, Nuevo León, Mexico.
Objective: There is an ongoing debate regarding the optimal treatment for craniosynostosis as diverse factors influence the election between endoscopic and open surgery. Previous evidence favors endoscopic procedures. However, evidence remains unfulfilled by a limited number of patients and clustered in very few centers worldwide making it difficult to define it as a replicable technique in different populations.
View Article and Find Full Text PDFMaterials (Basel)
September 2024
Department of Environmental Protection Engineering, Faculty of Environmental Engineering, Wroclaw University of Science and Technology, Wybrzeze Wyspianskiego 27, 50-370 Wroclaw, Poland.
This article addresses manufacturing structures made via injection molding from biodegradable materials. The mentioned structures can be successfully used as energy-absorbing liners of all kinds of sports helmets, replacing the previously used expanded polystyrene. This paper is focused on injection technological tests and tensile tests (in quasi-static and dynamic conditions) of several composites based on a PLA matrix with the addition of other biodegradable softening agents, such as PBAT and TPS (the blends were prepared via melt blending using a screw extruder with mass compositions of 50:50, 30:70, and 15:85).
View Article and Find Full Text PDFSci Rep
September 2024
Department of Mechanical Engineering, College of Engineering, Shantou University, Shantou, 515063, China.
Injection molding is a common plastic processing technique that allows melted plastic to be injected into a mold through pressure to form differently shaped plastic parts. In injection molding, in-mold electronics (IME) can include various circuit components, such as sensors, amplifiers, and filters. These components can be injected into the mold to form a whole within the melted plastic and can therefore be very easily integrated into the molded part.
View Article and Find Full Text PDFJ Craniofac Surg
January 2025
Division of Pediatric Neurosurgery, British Columbia Children's Hospital, Vancouver, British Columbia, Canada.
Endoscopy-assisted craniectomy with lateral osteotomies and postoperative helmet molding therapy is a widely used approach in managing sagittal suture craniosynostosis. Generally, the incisions are placed just posterior to the anterior fontanel and just anterior to the posterior fontanel and lambdoid sutures, and accurate incision placement optimizes the safe separation of the superior sagittal sinus. The authors present their 10 year experience with an ultrasound-assisted approach to identify the lambdoid sutures and precisely place the skin incisions.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!