Background: Multichannel tactile stimulation devices is need to investigate human finger population receptive field (pRF) characteristics in the primary somatosensory cortex during functional magnetic resonance imaging (fMRI).

Purpose: To accurately characterize right-hand somatosensory representation based on the Bayesian pRF model.

Study Type: Prospective.

Population: A water phantom and six healthy participants (four males, mean 23.8 years old).

Field Strength/sequence: T1-weighted magnetization-prepared rapid gradient-echo, T2*-weighted echo planar imaging at 3 T.

Assessment: The piezoelectric actuated tactile stimulation device consisted of execution unit and control unit. The output performance of the device was measured by a laser displacement sensor. The effect of the device on images' signal-to-noise ratio (SNR) was measured by phantom experiments. The activation representation arrangement order, relative volumes, and receptive field size of the right hand were assessed during the along-digits and cross-digits paradigms.

Statistical Tests: The normality of the data was tested by the Shapiro-Wilk method. A paired-sample t test was performed to test pRF characteristics for all digit pairings. The significance level was set to P = 0.05 (false discovery rate [FDR] correct).

Results: Percussive stimulation provided by the piezoelectric actuated tactile stimulator had a stable displacement (2.64 mm) over a wide range of vibration frequencies (0-30 Hz). The output delay of the device was 1 millisecond. The device did not affect the image's SNR (without the device: SNR = 138.24 ± 7.87, temporal SNR [TSNR] = 440.03 ± 52.08. With the device: SNR = 138.06 ± 8.44, TSNR = 438.52 ± 56.38. P  = 0.88, P  = 0.46). Representations of right-hand fingers showed the same arrangement order in both experiments (D1-D5 arranged along the central sulcus). However, the relative volumes of D3 showed significant differences in S1 (P = 0.003). Among four subareas, the relative volumes of D3 were significantly different in area 1 (P = 0.047).

Data Conclusion: This developed stimulator, through experimental verification, could play a role in pRF mapping exploration.

Level Of Evidence: 2 TECHNICAL EFFICACY STAGE: 1.

Download full-text PDF

Source
http://dx.doi.org/10.1002/jmri.28173DOI Listing

Publication Analysis

Top Keywords

piezoelectric actuated
12
actuated tactile
12
tactile stimulation
12
receptive field
12
relative volumes
12
device
8
stimulation device
8
population receptive
8
somatosensory cortex
8
prf characteristics
8

Similar Publications

Piezoresistive Cantilever Microprobe with Integrated Actuator for Contact Resonance Imaging.

Sensors (Basel)

January 2025

Institute of Semiconductor Technology (IHT), Technische Universität Braunschweig, Hans-Sommer-Straße 66, 38106 Braunschweig, Germany.

A novel piezoresistive cantilever microprobe (PCM) with an integrated electrothermal or piezoelectric actuator has been designed to replace current commercial PCMs, which require external actuators to perform contact-resonance imaging (CRI) of workpieces and avoid unwanted "forest of peaks" observed at large travel speed in the millimeter-per-second range. Initially, a PCM with integrated resistors for electrothermal actuation (ETA) was designed, built, and tested. Here, the ETA can be performed with a piezoresistive Wheatstone bridge, which converts mechanical strain into electrical signals by boron diffusion in order to simplify the production process.

View Article and Find Full Text PDF

The high degree of freedom (DoF) shape morphing widely exists in biology for mimicry, camouflage, and locomotion. Currently, a lot of bionic soft/flexible actuators and robots with shape-morphing functions have been developed to realize conformity, grasp, and movement. Among these solutions, two-dimensional responsive materials and structures that can shape morph into different three-dimensional configurations are valuable for creating reversible high DoF shape morphing.

View Article and Find Full Text PDF

We present an active alignment and stabilization control system for laser setups based on a thin-disk regenerative amplifier. This method eliminates power and pointing instability during the warm-up period and improves long-term stability throughout the entire operation. The alignment method is based on a four-mirror control system consisting of two motorized mirrors placed within the regenerative amplifier cavity, two additional motorized mirrors external to the amplifier cavity, and four camera detectors.

View Article and Find Full Text PDF

Piezoelectric materials directly convert between electrical and mechanical energies. They are used as transducers in applications such as nano-positioning and ultrasound imaging. Improving the properties of these devices requires piezoelectric materials capable of delivering a large longitudinal strain on the application of an electric field.

View Article and Find Full Text PDF

PET-PZT Dielectric Polarization: Electricity Harvested from Photon Energy.

Micromachines (Basel)

December 2024

Department of Chemical and Biological Engineering, Illinois Institute of Technology, Chicago, IL 60616, USA.

The effect of residual stress or heat on ferroelectrics used to convert photons into electricity was investigated. The data analysis reveals that when the PET-PZT piezoelectric transducer is UV-irradiated with a 405 nm wavelength, it becomes a photon-heat-stress electric energy converter and capacitator. Our objective was to evaluate the PET-PZT photon-heat-stress electric energy conversion performance and the role of the light's wavelength and intensity.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!