In order to solve the problem that the built-in parallel bond model in the discrete element software cannot adequately simulate the post-peak fracture behavior of quasi-brittle materials, a linear cohesive model was established. First, two particles are used to simulate the interface constitutive behavior in different modes. The results show that the new model can better simulate the behavior of Mode-I fracture, Mode-II fracture, and Mixed-mode fracture. Then, the influence of micro-parameters on the newly constructed constitutive model is analyzed, which provides a basis for the determination of micro-parameter values. Finally, the proposed softening model is applied to a three-point bending test of mortar, and the fracture behavior obtained is compared to the acoustic emission results. The simulation results also show that the constitutive model we built can be used to simulate the fracture behavior of quasi-brittle materials such as mortar and concrete.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8911574 | PMC |
| http://dx.doi.org/10.3390/ma15051964 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Experimental Study on the Size Effect of Compression-Shear Fracture Characteristics of Rock-like Materials Containing Open Cracks.
Materials (Basel)
December 2024
Engineering Research Center of Diagnosis Technology and Instruments of Hydro-Construction, Chongqing Jiaotong University, Chongqing 400074, China.
Understanding fracture mechanics in rock-like materials under compression-shear condition is critical for predicting failure mechanisms in various engineering applications, such as mining and civil infrastructure. This study conducted uniaxial compression tests on cubic gypsum specimens of varying sizes (side lengths of 75 mm, 100 mm, 125 mm, and 150 mm) and crack inclination angles (ranging from 0° to 90°) to assess the size effect on fracture behavior. The effects of specimen size and crack inclination on fracture characteristics, including strength, failure mode, and crack initiation angle, were analyzed based on the maximum tangential stress (MTS) criterion and the generalized maximum tangential stress (GMTS) criterion, with relative critical size (α) and relative openness ().
View Article and Find Full Text PDFA proposal for the combined analysis of bone quantity and quality of human cortical bone by quasi-brittle fracture mechanics.
J Biomech
November 2024
School of Mechanical Engineering, Purdue University, United States of America. Electronic address:
Quasi-brittle fracture mechanics is used to evaluate fracture of human cortical bone in aging. The approach is demonstrated using cortical bone bars extracted from one 92-year-old human male cadaver. In-situ fracture mechanics experiments in a 3D X-ray microscope are conducted.
View Article and Find Full Text PDFMicrostructural Characterization of Friction Stir Welds of Aluminum 6082 Produced with Bobbin Tool.
Materials (Basel)
September 2024
Faculty of Metal Engineering and Industrial Computer Science, AGH University of Science and Technology, 30-059 Kraków, Poland.
Article Synopsis
- * The weld microstructures were analyzed using various microscopy techniques, revealing fine, equiaxed grains and distinct features between the advancing and retreating sides of the welds.
- * Mechanical tests showed that the 280/280 welds had higher tensile strengths but lower hardness compared to the 450/450 welds, and the fracture behavior differed significantly, with 280/280 showing ductile failure versus the quasi-brittle failure of 450/450.
Comparing ceramic Fischer-Koch-S and gyroid TPMS scaffolds for potential in bone tissue engineering.
Front Bioeng Biotechnol
August 2024
Department of Mechanical Engineering, Colorado State University, Fort Collins, CO, United States.
Article Synopsis
- Triply Periodic Minimal Surfaces (TPMS), specifically Fischer-Koch-S (FKS) scaffolds, show promising properties for bone tissue engineering (BTE) compared to the more commonly used Gyroid scaffolds, particularly in terms of strength and energy absorption.
- While FKS scaffolds have been previously fabricated in metals and polymers, this study is the first to create them using a ceramic material suitable for BTE, finding that they are 32% stronger and absorb 49% more energy than Gyroid scaffolds with similar porosity.
- The study suggests that FKS scaffolds could be more effective for applications prioritizing dense bone and strength in BTE, despite a slight decrease in permeability.
Influence of Polymer Fibre Reinforcement on Concrete Anchor Breakout Failure Capacity.
Polymers (Basel)
August 2024
Faculty of Architecture and Civil Engineering, TU Dortmund University, 44227 Dortmund, Germany.
With the increasing use of fibre-reinforced concrete, e.g., in industrial floor and tunnel construction, the associated fastening technology in this material has increasingly become the focus of scientific attention in recent years.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!