These data were acquired to estimate the parameters of a closed form solution of a one-dimensional transient convection heat diffusion PDE. The purpose was to demonstrate that the model could be used to determine the thermal conductivity. The system was tested for a wide range of thermal conductivity, 15-400 W/mK, in order to verify that the method was applicable for various materials. The data reported here refer to the study in the research articles, "Material Thermal Properties Estimation Via a One-Dimensional Transient Convection Model" [1] and "Influence of porosity on the thermal, electrical, and mechanical performance of selective laser melted stainless steel" [2]. The dataset contains the raw data obtained from the temperature acquisition system as well as the processed results from a Python program to determine the thermal conductivity from a forced convection, transient one-dimensional heat diffusion equation.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8813594 | PMC |
| http://dx.doi.org/10.1016/j.dib.2021.107632 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Transforming an ATP-dependent enzyme into a dissipative, self-assembling system.
Nat Chem Biol
January 2025
Department of Chemistry and Biochemistry, University of California, San Diego, La Jolla, CA, USA.
Nucleoside triphosphate (NTP)-dependent protein assemblies such as microtubules and actin filaments have inspired the development of diverse chemically fueled molecular machines and active materials but their functional sophistication has yet to be matched by design. Given this challenge, we asked whether it is possible to transform a natural adenosine 5'-triphosphate (ATP)-dependent enzyme into a dissipative self-assembling system, thereby altering the structural and functional mode in which chemical energy is used. Here we report that FtsH (filamentous temperature-sensitive protease H), a hexameric ATPase involved in membrane protein degradation, can be readily engineered to form one-dimensional helical nanotubes.
View Article and Find Full Text PDFApplying Resin Radial Injection for Manufacturing Fiber-Reinforced Polymer Composite: Advanced Mathematical Modeling and Simulation.
Polymers (Basel)
December 2024
Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande 58429-900, PB, Brazil.
Recently, the liquid composite molding technique (LCM) has been used for producing fiber-reinforced polymer composites, since it allows the molding of complex parts, presenting good surface finishing and control of the mechanical properties of the product at the end of the process. Studies in this area have been focused on resin transfer molding (RTM), specifically on the resin rectilinear infiltration through the porous preform inserted in the closed cavity neglecting the sorption effect of the polymeric fluid by the reinforcement. Thus, the objective of this work is to predict resin radial flow in porous media (fibrous preform), including the effect of resin sorption by fibers considering a one-dimensional approach.
View Article and Find Full Text PDFImpacts of lateral conductive heat flow on ground temperature and implications for permafrost modeling.
Sci Rep
December 2024
Canada Centre for Remote Sensing, Canada Centre for Mapping and Earth Observation, Natural Resources Canada, 580 Booth Street, Ottawa, ON, K1A 0E4, Canada.
Permafrost ground temperature and its spatial distribution are usually calculated using one-dimensional models based on heat flow in the vertical direction. Here, we theoretically calculated the impacts of lateral conductive heat flow on ground temperature under equilibrium and transient conditions. The results show that lateral heat flow has strong impacts on ground temperature, especially in deep ground.
View Article and Find Full Text PDFResearch on the characteristics and protection of water hammer in long-distance dual-pipe water supply systems.
PLoS One
December 2024
School of Water Conservancy, North China University of Water Resources and Electric Power, Zhengzhou, Henan, China.
Hydraulic transients in long-distance pressurized water pipelines significantly impact their normal operation. This study develops a one-dimensional mathematical model for pressurized water pipelines using the method of characteristics and incorporates water hammer equations for dual-pipeline systems. The model is validated with experimental data, and simulations are conducted under real engineering conditions, focusing on valve closure operations.
View Article and Find Full Text PDFImpact of Aspect Ratio on Charge Carrier Dynamics and Efficiency Enhancement in CdSe/CdS Dot-in-Rod Nanostructures for Photocatalytic Hydrogen Evolution.
J Phys Chem Lett
December 2024
Department of Materials Science, National University of Tainan, Tainan 700301, Taiwan.
We demonstrated that the aspect ratio (AR)-tunable CdSe/CdS dot-in-rod (DiR) nanostructures with quasi-type-II band structure were successively synthesized using the hot injection method. When the AR of CdSe/CdS DiR was tuned from 10 to 37, the exciton localization efficiency along the longitudinal CdS rod shell decreased from 57.9 to 15.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!