The retained austenite (RA) in advanced high-strength steel (AHSS) grades, such as dual-phase (DP) steels, plays an important role on their formability. Thanks to the transformation-induced plasticity (TRIP) effect that occurs during the mechanically induced transformation of RA into martensite, additional ductility is obtained. Martensite has a higher flow stress than austenite; hence, the transformation results in an apparent hardening, which is beneficial for the stability of deformation. The stability of RA at a given temperature strongly depends on its carbon content, which, in AHSS, is not uniform but distributed. The aim of this study is to build a model that predicts the transformation as well as TRIP in a DP steel grade with RA. A physics-based kinetic model is presented that captures the transformation of retained austenite based on the thermodynamic driving force of the applied stress. A direct analytical estimate of transformation plasticity is provided, which is consistent with the kinetic model. Transformation kinetics is incorporated in a self-consistent, mean-field homogenization-based constitutive model. Finally, an indication of the effect of transformation of retained austenite on formability is given.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8778630 | PMC |
| http://dx.doi.org/10.3390/ma15020498 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Nanosized κ-Carbide and B2 Boosting Strength Without Sacrificing Ductility in a Low-Density Fe-32Mn-11Al Steel.
Nanomaterials (Basel)
December 2024
Analytical and Testing Center, Northeastern University, Shenyang 110819, China.
High-performance lightweight materials are urgently needed because of energy savings and emission reduction. Here, we design a new steel with a low density of 6.41 g/cm, which is a 20% weight reduction compared to the conventional steel.
View Article and Find Full Text PDFOn the Use of Cyclic Cryogenic Treatment to Improve the Properties of High-Speed Steel.
Materials (Basel)
December 2024
Faculty of Mechanical Engineering, Lublin University of Technology, ul. Nadbystrzycka 38D, 20-618 Lublin, Poland.
Cryogenic treatment is a process of controlled gradual cooling of the workpiece to a temperature ranging from -60 °C to even below -190 °C, holding the workpiece at this temperature and then slowly reheating it to ambient temperature. According to the current state of knowledge, the purpose of cryogenic treatment is to reduce the concentration of retained austenite by transforming it into hard martensite under low-temperature treatment. The retained austenite reduction in steels results in improved hardness, impact strength, and wear resistance.
View Article and Find Full Text PDFEffect of Al Element on Retained Austenite, Residual Compressive Stress, and Contact Fatigue Life of Carburized and Quenched 20MnCr5 Steel Gear.
Materials (Basel)
November 2024
School of Mechanical Engineering, Guangxi University, Nanning 530004, China.
To improve the contact fatigue life of gears, we studied the effect of adding a certain proportion of the Al element to a 20MnCr5 steel FZG spur gear under different heat treatment processes, characterizing the retained austenite and residual compressive stress on the tooth surface. The stability of the microstructure grain size on the gear surface under different heat treatment processes was studied, and the surface microstructure, phase structure, and composition of the gear were characterized using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The changes in the retained austenite content and grain size on the gear surface at a microscale of 2-100 μm were investigated.
View Article and Find Full Text PDFEffect of Deformed Prior Austenite Characteristics on Reverse Phase Transformation and Deformation Behavior of High-Strength Medium-Mn Steel.
Materials (Basel)
November 2024
State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819, China.
Article Synopsis
- * The research showed that deformation hindered the recovery and recrystallization of prior austenite during hot rolling, leading to a refined grain size and increased shear transformation resistance in the resulting martensite.
- * The combination of enhanced intercritical austenite nucleation and the transformation-induced plasticity (TRIP) effect resulted in optimal mechanical properties, including 748 MPa yield strength, 952 MPa tensile strength, and 26.2% total elongation.
The Effect of Heating Rate on the Microstructure Evolution and Hardness of Heterogeneous Manganese Steel.
Materials (Basel)
October 2024
Collaborative Innovation Center of Steel Technology, University of Science and Technology Beijing, Beijing 100083, China.
The use of a rapid heating method to achieve heterogeneity of Mn in medium-manganese steel and improve its comprehensive performance has been widely studied and these techniques have been widely applied. However, the heating rate (from α to γ) has not received sufficient attention with respect to its microstructure-evolution mechanism. In this study, the effect of heating rate on the microstructure evolution and hardness of heterogeneous medium-manganese steel was investigated by using X-ray diffraction (XRD), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), transmission electron microscopy (TEM) and DICTRA simulation.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!