Introduction: The aim of this study was to evaluate the clinical outcomes following treatment of distal radial fractures using intramedullary elastic wires with a combination of either cast immobilisation or external fixation.
Materials And Methods: A total of 42 patients (24 females and 18 males) aged 40 to 78 years who presented with displaced and unstable, closed or grade I open, extra- and/or intra-articular fractures of the distal radius were included in the study. Twenty-seven fractures were AO/OTA Type A2-A3 and 15 Type C1-C2. Twenty-four patients were treated with antegrade intramedullary (IM) fixation with elastic wires followed by cast immobilisation and 18 required an external fixator in lieu of casting.
Results: Final follow-up evaluation was conducted 12 months post-surgery using Sarmiento's modification of Lindstrom criteria and the demerit point system of Gartland and Werley. Successful fracture union was observed in all patients between eight to 14 weeks. Using Sarmiento's modification of Lindstrom criteria, 12 patients (28.6%) had excellent, 23 (54.8%) had good and 7 (16.6 %) had fair results. Based on the functional evaluation using the demerit point system of Gartland and Werley, 13 patients (31%) had excellent, 25 (59.5%) had good and four (9.5%) had fair results. None of the patients had a poor outcome using either of these criteria. Although a fracture union rate of 100% was confirmed clinically and radiographically, eight out of the 42 patients had minor complications in our study. One patient had uneventful IM migration of the wires, one patient reported a feeling of wire loosening, three patients complained of joint stiffness and soft tissue irritation, and three others reported on-going pain. The total cost of all implants used per case was less than INR 1,000.
Conclusions: Good to excellent functional and radiographic outcomes with easy to manage complications are achieved with the techniques described. Patient selection is key to determining which particular method should be prescribed in a given case.
Download full-text PDF |
Source |
---|---|
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8667235 | PMC |
http://dx.doi.org/10.5704/MOJ.2111.006 | DOI Listing |
Dent J (Basel)
December 2024
Research Center for Digital Technologies in Dentistry and CAD/CAM, Department of Dentistry, Faculty of Medicine and Dentistry, Danube Private University, Steiner Landstraße 124, 3500 Krems an der Donau, Austria.
: Traditional methods for palatal expansion using fixed appliances often face limitations in comfort and aesthetics. In comparison, aligner therapy has limitations, particularly regarding maxillary expansion. The aim of this study is to examine the biomechanical properties regarding the wire diameter and bending of different stainless steel wires to evaluate their potential for incorporation into maxillary aligner therapy.
View Article and Find Full Text PDFBMC Musculoskelet Disord
December 2024
Experimental Orthopaedics, Department of Orthopaedics and Traumatology, Medical University of Innsbruck, Innsbruck, 6020, Austria.
Bioinspir Biomim
January 2025
Biomimetics Laboratory, Auckland Bioengineering Institute, Auckland, New Zealand.
The propulsive fins of ray-finned fish are used for large scale locomotion and fine maneuvering, yet also provide sensory feedback regarding hydrodynamic loading and the surrounding environment. This information is gathered via nerve cells in the webbing between their fin rays. A similar bioinspired system that can gather force feedback from fin motion could enable valuable insight into robotic underwater locomotion improving swimming efficiency and orientation.
View Article and Find Full Text PDFPolymers (Basel)
November 2024
School of Materials and Chemistry Engineering, Minjiang University, Fuzhou 350108, China.
This study focuses on the development of polymer-bioglass composite bone scaffolds for the treatment of bone defects. PCL particles and 45s5 bioglass powder were employed as raw materials to fabricate PCL/45s5 composite wires with mass fractions of 5 wt%, 10 wt%, and 20 wt% via the twin-screw extrusion method. A cylindrical porous model was established using 3D modeling software, and a porous composite scaffold was constructed through the melt deposition manufacturing process.
View Article and Find Full Text PDFJ Contemp Dent Pract
July 2024
Department of Oral Pathology, SRM Dental College, Chennai, Tamil Nadu, India, Phone: +91 9500058376, e-mail:
Aim And Objective: To evaluate and compare the impact of nanocoatings made of oxides of Aluminum, Titanium, and Zirconium, on the frictional resistance on three types of superelastic orthodontics archwires namely; nickel titanium, copper nickel titanium and low hysteresis nickel titanium.
Materials And Methods: There are120 archwire segments of equal dimensions were divided into four groups ( = 30) with 10 samples each of low hysteresis superelastic archwires; NiTi archwires and CuNiTi archwires. While group A were uncoated, other groups were nanocoated with group B: Aluminum oxide; group C: Titanium dioxide; group D: Zirconium oxide respectively.
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!