Abdominal injury is a frequent cause of death for trauma patients, and early recognition is essential to limit fatalities. There is a need for a wearable sensor system for prehospital settings that can detect and monitor bleeding in the abdomen (hemoperitoneum). This study evaluates the potential for microwave technology to fill that gap. A simple prototype of a wearable microwave sensor was constructed using eight antennas. A realistic porcine model of hemoperitoneum was developed using anesthetized pigs. Ten animals were measured at healthy state and at two sizes of bleeding. Statistical tests and a machine learning method were used to evaluate blood detection sensitivity. All subjects presented similar changes due to accumulation of blood, which dampened the microwave signal ([Formula: see text]). The machine learning analysis yielded an area under the receiver operating characteristic (ROC) curve (AUC) of 0.93, showing 100% sensitivity at 90% specificity. Large inter-individual variability of the healthy state signal complicated differentiation of bleedings from healthy state. A wearable microwave instrument has potential for accurate detection and monitoring of hemoperitoneum, with automated analysis making the instrument easy-to-use. Future hardware development is necessary to suppress measurement system variability and enable detection of smaller bleedings.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8636634PMC
http://dx.doi.org/10.1038/s41598-021-02008-5DOI Listing

Publication Analysis

Top Keywords

wearable microwave
12
healthy state
12
microwave instrument
8
detect monitor
8
porcine model
8
machine learning
8
wearable
4
instrument detect
4
monitor traumatic
4
traumatic abdominal
4

Similar Publications

-CoFeO/TiCT/BNC Hybrid Aerogels with Modulation Impedance Matching for Electromagnetic Wave Absorption and Health Monitoring.

ACS Appl Mater Interfaces

January 2025

Key Laboratory of Advanced Materials for Facility Agriculture, Ministry of Agriculture, College of Materials and Energy, South China Agricultural University, Guangzhou 510642, China.

Given the limitations of single-function electromagnetic wave-absorbing materials (EWAMs) in meeting the evolving demands of complex usage scenarios, there is a growing need for structure-function integrated composites that offer a combination of microwave absorption, human monitoring, and thermal insulation. This study successfully synthesized two-dimensional (2D) TiCT MXene via selective etching of Al from the TiAlC MAX phase. By introducing MXene into a composite of hydroxylated CoFeO nanoparticles (-CFO NPs) and bacterial nanocellulose (BNC) to modulate the electromagnetic performance of the EWAMs.

View Article and Find Full Text PDF

Effect of CNF ratio and pressure on structural and electrochemical performance of hybrid hydrogel for flexible free-standing electrode and sensors.

Carbohydr Polym

February 2025

State key laboratory base of eco-chemical Engineering, College of Chemical Engineering, Qingdao University of Science and Technology, 53 Zhengzhou Road, Qingdao, Shandong province 266042, PR China. Electronic address:

Article Synopsis
  • A 2D flexible hydrogel (GO/CNF) is created by combining graphene oxide (GO) with cellulose nanofiber (CNF) using microwave-assisted hydrothermal methods, resulting in a superhydrophilic material with a layered structure.
  • * The optimal mass ratio of GO to CNF is 3:1, leading to a specific capacitance of 295 F/g and improved electrochemical performance when used as free-standing electrodes in a three-electrode system.
  • * The enhanced properties of the hydrogel, especially at a press pressure that increases hydrophilicity, suggest its potential for use in flexible solid-state supercapacitors, wearable electronics, and biological signal detection with a high energy density of 20.6
View Article and Find Full Text PDF

The triboelectric nanogenerator (TENG) has demonstrated exceptional efficiency in harvesting diverse forms of mechanical energy and converting it into electrical energy. This technology is particularly valuable for powering low-energy electronic devices and self-powered sensors. Most traditional TENGs use single-sided patterned friction pairs, which restrict their effective contact area and overall performance.

View Article and Find Full Text PDF

The integration of flexible sensors into human-machine interfaces (HMIs) is in increasing demand for intuitive and effective manipulation. Traditional glove-based HMIs, constrained by nonconformal rigid structures or the need for bulky batteries, face limitations in continuous operation. Addressing this, we introduce yarn-based bend sensors in our smart glove, which are wirelessly powered and harvest energy from a fully textile 5.

View Article and Find Full Text PDF

The single-input-single-output technology experiences loss of data in the communication channel due to the receiving antenna undergoing fading of the signal impinged on it. Today's need is faster data transfer with multiple applications in the single antenna with multiple-identical radiating elements, leading to multiple-input-multiple-outputDWMB (MIMODWMB) technology. The MIMODWMB configuration with multi-band capability is the objective of the proposed work with applications ranging between microwave-millimeterWave bands.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!