Purpose: To compare the flexural properties and the adhesion of Lactobacillus salivarius (LS), Streptococcus mutans (SM), and Candida albicans (CA) on heat-polymerized (CV), CAD-CAM milled (CAD), or 3D-printed (3D) Poly (methylmethacrylate) (PMMA).
Methods: Ultimate Flexural Strength (UFS), Flexural Strain (FS) (%) at Flexural Strength, and Flexural Modulus (FM) of specimens (65.0×10.0×3.3 mm) from each PMMA group (n=6) were calculated by using the 3-point bending test. The surface roughness profiles (R) were measured before and after polishing with a contact profilometer. LS, SM, and CA adhesion on PMMA specimens (n=18) (10 mm in diameter, 3 mm in height) was assessed after 90 minutes and 16 hours by using scanning electron microscopy. The Kruskal-Wallis test with post hoc analysis was performed to compare the groups (alpha=0.05).
Results: Mean UFS values were 80.79±7.64 MPa for CV, 110.23±5.03 MPa for CAD, and 87.34±6.39 MPa for 3D. Mean FS values were 4.37±1.04% for CV, 4.71±0.62% for CAD, and 6.19±0.13 % for 3D. Mean FM values were 2542±301 MPa for CV, 3435±346 MPa for CAD, and 2371±197 MPa for 3D. CAD had the lowest average R value (0.29±0.16 µm) before polishing, and bacterial adhesion after 90 minutes of incubation. R value and microbial adhesion were not different amongst groups after polishing and 16 hours of incubation, respectively.
Conclusion: The CAD group displayed the best flexural properties, except for FS, the lowest roughness before polishing and bacterial adhesion after 90 minutes of incubation. All tested PMMAs had similar surface roughness after polishing, and microbial adhesion after 16 hours of incubation.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.2186/jpr.JPR_D_21_00116 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Fracture Resistance and Initial Penetration Time of a Novel Zirconia Crown Design for Simplifying Future Endodontic Treatment: An In Vitro Study.
Dent J (Basel)
November 2024
Department of Prosthetic Dental Science, College of Dentistry, Jazan University, Jazan 45142, Saudi Arabia.
: This study aimed to investigate the fracture strength of a novel-designed Zirconia crown before and after access opening, and to evaluate the mode of fracture and the time needed for initial penetration through the crown. : This study involved the design and testing of 60 zirconia crowns, divided into three groups (20 crowns each) to compare different structural designs. Group 1 (Control) used a conventional full zirconia crown.
View Article and Find Full Text PDFEvaluation of the shear bond strength of surface-treated Cobalt-Chromium metal crowns on corticobasal® implant abutments cemented using different luting agents.
J Stomatol Oral Maxillofac Surg
December 2024
Reader, Department of Periodontics, Saveetha Dental College and Hospitals, Saveetha Institute of Medical and Technical Sciences, Saveetha University, Chennai 600077, Tamil Nadu, India.. Electronic address:
Purpose: This in-vitro study aimed to compare the shear bond strength (SBS) of cobalt-chromium (Co-Cr) crowns on Corticobasal® implant abutments, evaluating the effects of two surface treatments and two luting agents.
Materials And Methods: Thirty Co-Cr crowns were fabricated using CAD-CAM technology with a direct metal laser sintering process and divided into three groups based on surface treatment: Group I (untreated), Group II (sandblasted with 50 μm Al₂O₃), and Group III (Er: YAG laser etching). Each group was further subdivided based on luting cement: Sub group A (GC Fuji Plus) and Sub group B (Rely X U200).
Purpose: The aim of this article was to present a method for predicting dental materials lifetime, using in vitro thermally accelerated ageing. The technique was tested to compare the behavior of 3 resin base materials for denture.
Materials And Methods: Bar-shaped samples of the poly(methyl methacrylate) PMMA based-resin Probase Hot (Probase), CAD/CAM disc Ivobase CAD (IvoCAD) and high-impact resin IvoCAP were aged in artificial saliva for 15, 30, 45, 60, 90, 120 and 180 days at 55°C, 75°C and 90°C.
Bonding super translucent multilayered monolithic zirconia to different foundation materials: an invitro study.
BMC Oral Health
December 2024
Department of Fixed Prosthodontics, Faculty of Dentistry, Mansoura University, Mansoura, Dakahlia Governorate, Egypt.
Background: The objective of this study was to investigate the effect of bonded substrate, zirconia surface conditioning and the interaction between them on the shear bond strength of monolithic zirconia.
Methods: Forty-eight monolithic zirconia discs were CAD-CAM fabricated and divided into two groups according to surface treatment either as milled and universal primer application (Monobond N, Ivoclar-Vivadent) (P) or sandblasting then universal primer application (Monobond N) (SP). Each main group was further divided into three test groups according to the bonded substrate: dentin (DSP, DP), composite (CSP, CP) or resin modified glass ionomer (RMGI) (GSP, GP).
Airborne-Particle Abrasion vs. Hydrofluoric Acid Etching of Dental Ceramics: Impact on the Tensile Bond Strength.
Materials (Basel)
November 2024
Department of Prosthetic Dentistry, University Hospital, LMU Munich, 80336 Munich, Germany.
Article Synopsis
- The study compared airborne-particle abrasion to hydrofluoric acid etching as a method for preparing silicate ceramic restorations for adhesive bonding.
- The research involved various substrates (feldspar, lithium silicate, and zirconia) undergoing different abrasion conditions, and evaluated surface characteristics and tensile bond strength after treatment.
- Results indicated that airborne-particle abrasion, particularly using 50 µm particles at 0.1 MPa, effectively enhances bond strength and surface roughness, suggesting it as a viable alternative to traditional etching methods for ceramics.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!