Interleaving composite laminates by nanofibers is a well-known method of increasing interlaminar fracture toughness. Among many possibilities, polycaprolactone (PCL) nanofibers is one of the best choices for toughening composite laminates. The influence of PCL on delamination mode of failure is considered before. However, the effect of PCL on other damage modes, such as fiber breakage and matrix cracking, is yet to be studied. In this study, the acoustic emission (AE) technique is applied to determine the effect of toughening composite laminates by PCL nanofibers on matrix cracking, fiber/matrix debonding, and fiber breakage failure mechanisms. For this purpose, mode I and mode II fracture tests are conducted on modified and non-modified glass/epoxy laminates. Three different methods, i.e., peak frequency, wavelet transform, and sentry function, are utilized for analyzing the recorded AE data from mode I test. The results show that applying PCL nanofibers not only increases the mode I critical strain energy release rate by about 38%, but also decreases different failure mechanisms by between 75 and 94%.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8588528 | PMC |
| http://dx.doi.org/10.3390/polym13213680 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Impact of compaction process on the carbon epoxy composite under varied environmental conditions.
Sci Rep
December 2024
Mechanical and Aerospace Engineering Department, United Arab Emirates University, 15551, Al Ain, United Arab Emirates.
Fibre-reinforced polymeric composites utilized in aerospace settings, experience varying environmental conditions throughout their operational lifespan. The major factors that can have adverse effects on their long-term performance are water and temperature. The present study investigates how the determinants such as water and temperature impact the structural integrity of plain weave woven carbon/epoxy laminated composites and further categorizing them into compacted and non-compacted groups.
View Article and Find Full Text PDFFailure analysis and size optimization of CFRP composite single-lap bonded joints based on the influence of multiple parameters.
Sci Rep
December 2024
College of Aerospace Engineering, Shenyang Aerospace University, Shenyang, 110136, China.
This paper had conducted tensile shear tests on single-lap joints (SLJs)bonded structures of carbon fiber reinforced resin matrix (CFRP) composite laminates with different overlap lengths, overlap widths, overlap model, adherend material, and adhesive layer thicknesses under two environments: room temperature dry state (RTD) and elevated temperature wet state (ETW). The failure modes were observed, and load-displacement curves were obtained. The microscopic morphology of the fracture surface was observed by scanning electron microscope (SEM).
View Article and Find Full Text PDFCollected data on bending, vibration, and push-out tests of shallow steel-timber composite beams-Nordic system.
Data Brief
December 2024
Tampere University, Faculty of Built Environment, P.O. Box 600, FI-33014 Tampere, Finland.
In a slim-floor structural system, beams and slabs are placed at the same level, reducing the overall floor height and material usage in vertical structures, thereby improving economic efficiency. The use of slim-floor structures is common practice in Finnish construction where these structures are typically constructed using hollow-concrete slabs and welded steel box beams. However, in Finland, only a few buildings utilise cross-laminated timber (CLT) slabs in slim-floor structures, and none have incorporated the composite action between CLT and steel beams.
View Article and Find Full Text PDFMultifunctionality and Processability of a Thermoplastic Based Gel Electrolyte Cell for the Realization of Structural Batteries.
J Phys Chem C Nanomater Interfaces
December 2024
Center for Transport Technologies, Battery Technologies, AIT Austrian Institute of Technology GmbH, Giefinggasse 2, Vienna 1210, Austria.
In this work, a battery layup consisting of a poorly flammable ionic liquid electrolyte and a poly(vinylidene fluoride--hexafluoropropylene) (PVdF-HFP) thermoplastic has been developed along with composite anode and cathode electrodes. The developed gel electrolyte exhibits feasible ionic conductivity of about 1 mS/cm at 30 °C. State-of-the-art active electrode materials, i.
View Article and Find Full Text PDFOne-Pot Synthesis of Multicentric DIL@PDIL Catalyst for Mild CO 2 Conversion to Cyclic Carbonates.
Chemistry
December 2024
Guangdong Pharmaceutical University, Guangzhou Higher Education Mega Center, 510006, Guangzhou, CHINA.
Among the various studies on CO2 utilization, the sustainable and cost-effective fixation of CO2 into cyclic carbonates remains one of the most intriguing subjects. To this end, a novel type of composite dicationic ionic liquid material, DIL@PDIL, was developed. This composite consists of a dicationic ionic liquid (DIL), DMAP[TMGH]Br, supported on a polymeric dicationic ionic liquid (PDIL), P-DVB/Im[TMGH]Br.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!