Assessing the transport and reactive processes of contaminants in freshwater streams is crucial in managing water resources sustainably. Particularly the hyporheic zone, the sediment-water interface where surface water and groundwater mix, may possess significant contaminant removal capacities due to its myriad physical, chemical, and microbiological processes. However, modelling approaches aiming at assessing the hyporheic zone's reactivity are either based on simple assumptions, such as, predefining the shape of the residence times distribution (RTD) function, or are computationally not feasible due to a too detailed system characterisation. In addition, parent-daughter reactions of contaminants are barely investigated. The present study introduces a numerical modelling framework for assessing hyporheic reactions of contaminant transformation reactions based on a non-parametric residence time approach combined with multiple sorption models and first-order removal reactions. The proposed framework uses natural electrical conductivity fluctuations to determine conservative transport properties and is demonstrated by interpreting time series of hyporheic point measurements of trace organic compounds, such as pharmaceuticals, and their transformation products using two commonly-used sorption models, namely the simple retardation and the first-order kinetic sorption model. The developed approach gives similar reaction rate coefficient estimates for all contaminants considered for both sorption models tested. The findings highlight that (i) the accurate shape of the RTD is most certainly important for reactive parameter determination and (ii) the daughter reaction rate coefficient may be underestimated if its parent transformation is ignored. The model provides reactive parameter estimates of contaminant transformation reactions with high parameter identifiability and informs which specific parent-daughter-pathway has occurred.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1016/j.watres.2021.117750 | DOI Listing |
Polymers (Basel)
December 2024
Institute of Chemistry, Federal University of Rio Grande do Sul (UFRGS), Bento Gonçalves 9500, Porto Alegre 90010-150, RS, Brazil.
This study reported a one-spot preparation of magnetic composite carbon (MCC@Fe) from microcrystalline cellulose (MC). The pure cellulose was impregnated in iron (III) chloride solution and carbonized at 650 °C. The MCC@Fe composite adsorbent underwent various characterization techniques.
View Article and Find Full Text PDFPolymers (Basel)
December 2024
Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande 58429-900, PB, Brazil.
Recently, the liquid composite molding technique (LCM) has been used for producing fiber-reinforced polymer composites, since it allows the molding of complex parts, presenting good surface finishing and control of the mechanical properties of the product at the end of the process. Studies in this area have been focused on resin transfer molding (RTM), specifically on the resin rectilinear infiltration through the porous preform inserted in the closed cavity neglecting the sorption effect of the polymeric fluid by the reinforcement. Thus, the objective of this work is to predict resin radial flow in porous media (fibrous preform), including the effect of resin sorption by fibers considering a one-dimensional approach.
View Article and Find Full Text PDFMolecules
December 2024
Department of Environmental Engineering, University of Warmia and Mazury in Olsztyn, Warszawska St. 117a, 10-957 Olsztyn, Poland.
This study aimed to investigate the effect of aminating waste newsprint paper with different aminating agents (ammonia/ammonia water, ethylenediamine, and diethylenetriamine) for the sorption efficiency of Reactive Black 5 (RB5) and Reactive Yellow 84 (RY84) dyes. To increase the amination efficiency, the paper material was pre-activated with epichlorohydrin. The scope of this study included the characterization of the sorbents tested (FTIR, elemental analysis, BET surface area, porosity, and pH), determination of the influence of pH on dye sorption efficiency, sorption kinetics, and the maximum sorption capacity of the dyes.
View Article and Find Full Text PDFMolecules
December 2024
Department of Analytical and Inorganic Chemistry, Faculty of Chemistry, University of Bialystok, Ciołkowskiego 1K, 15-245 Bialystok, Poland.
In this work, for the first time, the sorption behaviour of platinum and palladium on polyethylene microplastics (PE-MP) was studied. To simulate natural conditions, part of PE-MP was subjected to the ageing process in lake water under the influence of solar radiation. The original and aged PE-MP was characterised using elemental analysis, FT-IR, SEM-EDX, and nitrogen porosimetry methods.
View Article and Find Full Text PDFMaterials (Basel)
December 2024
Faculty of Chemistry, Jagiellonian University in Kraków, Gronostajowa 2 Str., 30-387 Kraków, Poland.
The large numbers of ion exchange resins used in various industries (food, pharmaceutitics, mining, hydrometallurgy), and especially in water treatment, are based on cross-linked polystyrene and divinylbenzene copolymers with functional groups capable of ion exchange. Their advantage, which makes them environmentally friendly, is the possibility of their regeneration and reuse. Taking into account the wide application of these materials, styrene-divinylbenzene resin with a quaternary ammonium functional group, AmberliteIRA402, was characterized using a well-known and widely used method, FT-IR spectroscopy.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!