A multilayer piezoelectric material was fabricated using piezoelectric materials with low-temperature sintering capabilities and high piezoelectric coefficients to develop a functionally superior piezoelectric speaker with a large-displacement deformation. A soft relaxor was utilized to prepare the component materials, with the optimized composition of the investigated piezoelectric ceramics represented by 0.2Pb((Zn0.8Ni0.2)13Nb23)O3-0.8Pb(Zr0.5Ti0.5)O3. Li2CO3 was added to assist the low-temperature sintering conducted at 875 °C, which yielded a multilayer piezoelectric material with superior properties (d33 = 500 pC N, kp = 0.63, g33 = 44 mV N). A multilayer piezoelectric actuator with a single-layer thickness of ~40 µm and dimensions of 12 × 16 mm was fabricated by tape casting the prepared green sheets. Finite element analysis revealed that the use of a PEEK film and a smaller silicone-rubber film as a composite in the diaphragm realized optimal frequency-response characteristics; the vibrations generated by the piezoelectric element were amplified. The optimal structure obtained via simulations was applied to fabricate an actual piezoelectric speaker with dimensions of 20 × 24 × 1 mm. The actual measurements exhibited a sound pressure level of ~75 dB and a total harmonic distortion ≤15% in the audible frequency range (250-20,000 Hz) at an applied voltage of 5 Vp.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8510374 | PMC |
| http://dx.doi.org/10.3390/ma14195795 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Microwave Surface and Lamb Waves in a Thin Diamond Plate: Experimental and Theoretical Investigation.
Ultrasonics
January 2025
Federal State Budgetary Institution , Technological Institute for Superhard and Novel Carbon Materials of National Research Centre, Kurchatov Institute, 108840 Moscow, Troitsk, Russian Federation.
Microwave surface and Lamb waves in a multilayered piezoelectric "Al-IDT/(AlSc)N/(001)[110] diamond" structure designed as a SAW resonator were studied using both the experimental and modeling methods. In this structure, it is possible to generate Rayleigh, surface horizontal (SH) and Lamb waves simultaneously. The successful excitation of Lamb waves at operating frequencies up to 20 GHz has been obtained.
View Article and Find Full Text PDFInterface Acoustic Waves in 128° YX-LiNbO/SU-8/Overcoat Structures.
Micromachines (Basel)
January 2025
Department of Astronautical, Electrical and Energy Engineering, University of Rome "La Sapienza", Via Eudossiana 18, 00184 Rome, Italy.
The propagation of interface acoustic waves (IAWs) in 128° YX-LiNbO/SU-8/overcoat structures was theoretically studied and experimentally investigated for different types of overcoat materials and thicknesses of the SU-8 adhesive layer. Three-dimensional finite element method analysis was performed using Comsol Multiphysics software to design an optimized multilayer configuration able to achieve an efficient guiding effect of the IAW at the LiNbO/overcoat interface. Numerical analysis results showed the following: (i) an overcoat faster than the piezoelectric half-space ensures that the wave propagation is confined mainly close to the surface of the LiNbO, although with minimal scattering in the overcoat; (ii) the presence of the SU-8, in addition to performing the essential function of an adhesive layer, can also promote the trapping of the acoustic energy toward the surface of the piezoelectric substrate; and (iii) the electromechanical coupling efficiency of the IAW is very close to that of the surface acoustic wave (SAW) along the bare LiNbO half-space.
View Article and Find Full Text PDFModeling and Characterization of Multilayer Piezoelectric Stacks via Dynamic Stiffness Method.
Micromachines (Basel)
December 2024
GREMAN UMR 7347 CNRS, Université de Tours, INSA Centre Val de Loire, 3 Rue de la Chocolaterie, 41000 Blois, France.
Multilayer piezoelectric stacks, which are multiple layers of piezoelectric materials placed on top of each other, are widely used to achieve precise linear movement and high-force generation. In this paper, a dynamic stiffness (DS) method for the dynamic vibration analysis of multilayer piezoelectric stacks is presented. First, the general solutions for all physical quantities of the three vibration contributions (i.
View Article and Find Full Text PDFFully biodegradable hierarchically designed high-performance nanocellulose piezo-arrays.
Sci Adv
January 2025
NEST, Istituto Nanoscienze-CNR and Scuola Normale Superiore, I-56127 Pisa, Italy.
While piezoelectric sensing and energy-harvesting devices still largely rely on inorganic components, biocompatible and biodegradable piezoelectric materials, such as cellulose nanocrystals, might constitute optimal and sustainable building blocks for a variety of applications in electronics and transient implants. To this aim, however, effective methods are needed to position cellulose nanocrystals in large and high-performance architectures. Here, we report on scalable assemblies of cellulose nanocrystals in multilayered piezoelectric systems with exceptional response, for various application scopes.
View Article and Find Full Text PDFSynergic Cellulose Nanofiber/Tourmaline Nanoparticle-Assembled Layered Piezoelectric Cryogels for High-Performance Airborne Particulate Filtration.
Small
December 2024
Fiber and Particle Engineering Research Unit, Faculty of Technology, University of Oulu, P.O. Box 4300, Oulu, 90014, Finland.
Here, hybrid stimuli-responsive (exhibiting pyroelectricity and piezoelectricity) porous cryogels are engineered by embedding tourmaline nanoparticles (TNs) in a cellulose nanofiber (CNF) skeleton to generate high-performance CNF-TN-based airborne particulate matter (PM) filters. First, single-layer hybrid cryogels with varying TN contents (0-5% w v) are assembled, and the design principles for multilayered filters are established based on a novel sequential pre-freezing and freeze-drying technique. As observed, the embedded TNs transformed the CNF network into a more homogeneous, isotropic, and firm structure, thus improving the structural integrity and thermal stability of the assembled cryogels while maintaining their ultrahigh porosity and low density.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!