Background: During notchplasty in anterior cruciate ligament (ACL) reconstruction, bone is excised from the lateral and roof area of the notch to widen the intercondylar space and avoid notch-graft impingement in extension. There are concerns that bone regrowth of the area will cause narrowing and increase the risk of complications.

Purpose: To determine the possibility of late narrowing of the notch after notchplasty using computed tomography (CT) analysis.

Study Design: Case series; Level of evidence, 4.

Methods: Measurements were performed on CT scans (axial and sagittal planes with knee in extension) in patients who had undergone single-bundle anatomic ACL reconstruction using hamstring graft. Two axial image levels were used: at the anterior outlet and the anterior one-eighth level of the notch. The maximum notch height and width, the notch width at one-third and two-thirds of the preoperative notch midwidth height, the maximum condylar width, and the surface area of the lateral half of the notch were measured preoperatively and at 1 week and 2 years postoperatively.

Results: Included were 20 consecutive patients (mean ± standard deviation age, 28 ± 7.3 years; follow-up, 24.2 ± 3.3 months). At the anterior notch outlet, the maximum notch width increased by 1.9 ± 1.7 mm at 1 week postoperatively and narrowed by 0.3 ± 1.1 mm at the final follow-up, while the maximum notch height increased by 1.7 ± 1.9 mm and narrowed by 0.8 ± 1.8 mm, respectively. At one-eighth of the roof length, the maximum notch width increased by 1.1 ± 1.7 mm at 1 week postoperatively and narrowed by 0.1 ± 1.1 mm at the final follow-up, and the maximum notch height increased by 1.2 ± 1.5 mm and narrowed by 0.5 ± 1.5 mm, respectively. All differences were statistically significant when comparing the pre- to the immediate postoperative measurements, and they were nonsignificant when comparing the immediate postoperative to the final follow-up measurements. The same applied for the ratio of maximum notch width to maximum condylar width, indicating no postoperative narrowing of the notch.

Conclusion: Notch size-shape after a 2-mm notchplasty did not change significantly in stable knees during the first 2 years after anatomic ACL reconstruction. Surgeons should consider performing this adjuvant technique when there is notch-graft impingement during surgery.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8435929PMC
http://dx.doi.org/10.1177/23259671211029228DOI Listing

Publication Analysis

Top Keywords

maximum notch
24
notch width
16
notch
14
acl reconstruction
12
notch height
12
final follow-up
12
computed tomography
8
notch-graft impingement
8
anatomic acl
8
maximum
8

Similar Publications

Glass short fiber-reinforced thermoplastics (GSFRTPs) are a cost-effective alternative to other short fiber-reinforced thermoplastics (SFRTPs). Their excellent mechanical properties make them a suitable material for components that require rigidity and light weight in widely diverse fields, including transportation and office automation equipment. The melt-mixing process is used to shorten glass fibers.

View Article and Find Full Text PDF

Pulmonary artery (PA) flow analysis is crucial for understanding the progression of pulmonary hypertension (PH). We hypothesized that PA flow characteristics vary according to PH etiology. In this study, we used 4D flow cardiovascular magnetic resonance imaging (CMR) to compare PA flow velocity and wall shear stress (WSS) between patients with pulmonary arterial hypertension (PAH) and those with heart failure with preserved ejection fraction and pulmonary hypertension (PH-HFpEF).

View Article and Find Full Text PDF

Although Mg-Li dual metal-ion batteries are proposed as a superior system that unite safety of Mg-batteries and performance of Li-ion based systems, its practical implantation is limited due to the lack of reliable high performance cathodes. Herein, we report a high-performance Mg-Li dual metal-ion battery system based on highly pseudocapacitive hierarchical TiO2-B nanosheet assembled spheres (NS) cathode. This 2D cathode displayed exceptional pseudocapacitance (a maximum of 93%) specific capacity (303 mAh/g at 25 mA/g), rate performance (210 mAh/g at 1A/g), consistent cycling (retain ~100% capacity for 3000 cycles at 1A/g), coulombic efficiency (nearly 100%) and fast-charging (~12.

View Article and Find Full Text PDF

High-Performance Solution-Processable Organic Light-Emitting Diode Based on a Narrowband Near-Ultraviolet Emitter and a Hot Exciton Strategy.

Angew Chem Int Ed Engl

December 2024

School of Materials Science and Engineering, Jiangsu Engineering Research Center of Light-Electricity-Heat Energy-Converting Materials and Applications, Jiangsu Collaborative Innovation Center of Photovoltaic Science and Engineering, Jiangsu Key Laboratories of Environment-Friendly Polymers, National Experimental Demonstration Center for Materials Science and Engineering, Changzhou University, Changzhou, 213164, P. R. China.

Achieving high efficiency narrowband near-ultraviolet (NUV) emitters in organic light emitting diode (OLED) is still a formidable challenge. Herein, a proof-of-concept hybridized local and charge transfer (HLCT) molecule, named ICz-BO, is prepared and characterized, in which both multiresonant (MR) skeletons are integrated via conjugation connection. A slightly distorted structure and weak intramolecular charge transfer (CT) interaction between two MR subunits lead to a high-lying reverse intersystem crossing (h-RISC) channel of T→S, also evidenced by both experimental and calculated results.

View Article and Find Full Text PDF

Influence of Specimen Width on Crack Propagation Process in Lightly Reinforced Concrete Beams.

Materials (Basel)

November 2024

State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology, Dalian 116024, China.

Article Synopsis
  • Traditional 2D models for studying concrete fractures often overlook how specimen width affects crack behavior, particularly in reinforced concrete beams with varying crack lengths.
  • A 3D numerical method was developed to simulate crack propagation in lightly reinforced concrete beams, utilizing nonlinear spring elements to accurately represent concrete softening and bond-slip between steel and concrete.
  • Comparisons with experimental data showed that the 3D model provided more accurate load-displacement curves, revealing that 2D models significantly overestimate external loads during the initial loading stage.
View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!