Every year, ceramic tile factories and the iron smelting industry produce huge amounts of waste ceramic tiles and blast furnace slag (BFS), respectively. In the field of construction materials, this waste can be used as a raw material for binders, thus reducing landfill waste and mitigating environmental pollution. The purpose of this study was to mix waste ceramic powder (WCP) into BFS paste and mortar activated by sodium silicate and sodium hydroxide to study its effect on performance. BFS was partially replaced by WCP at the rate of 10-30% by weight. Some experimental studies were conducted on, for example, the fluidity, heat of hydration, compressive strength testing, ultrasonic pulse velocity (UPV), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), electrical resistivity, sulfuric acid attack, and chloride ion diffusion coefficient. Based on the results of these experiments, the conclusions are: (1) increasing the amount of waste ceramic powder in the mixture can improve the fluidity of the alkali-activated paste; (2) adding waste ceramic powder to the alkali-activated mortar can improve the resistance of the mortar to sulfuric acid; (3) adding waste ceramic powder to the alkali-activated mortar can increase the diffusion coefficient of chloride ions; (4) the early strength of alkali-activated mortar is affected by the Ca/Si ratio, while the later strength is affected by the change in the Si/Al ratio.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8398777 | PMC |
| http://dx.doi.org/10.3390/polym13162817 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Evaluating energy consumption patterns in novel foamed ternary alkali-activated masonry blocks.
Sci Rep
January 2025
Sustainability Solutions Research Lab, Faculty of Engineering, University of Pannonia, Egyetem Str. 10, Veszprém H, 8200, Veszprém, Hungary.
This study endeavors to tackle the energy requirements of the building sector by employing passive design strategies. However, there exists a dearth of comprehension regarding the energy efficiency performance of foamed alkali-activated materials. To bridge this research gap, the study proposes a solution in the form of a thermally proficient wall material crafted from ceramic tile dust (CTD), class C fly ash (FA), and Ground Granulated Blast-Furnace Slag (GGBS), all of which are industrial by-products.
View Article and Find Full Text PDFPreparation of ion imprinted EDTA modified chitosan-magnetic graphene oxide for selective recovery and adsorption mechanism of Ce(III).
Sci Total Environ
January 2025
Inner Mongolia Key Laboratory of Advanced Ceramic Material and Devices, Baotou 014010, China.
Selective recovery of rare earth elements (REEs) from environmental waste is strategically significant. Herein, Ce(III) imprinted EDTA modified chitosan-magnetic graphene oxide (IIP-EDTA-CS-MGO) was prepared for selective recovery of Ce(III). Furthermore, adsorption mechanism was clarified based on versatile adsorption fittings and spectroscopic tests.
View Article and Find Full Text PDFBinding Kinetics of Self-Assembled Monolayers of Fluorinated Phosphate Ester on Metal Oxides for Underwater Aerophilicity.
Langmuir
January 2025
Department of Physics, Chair of Biophysics, Friedrich-Alexander-Universität Erlangen-Nürnberg, Henkestrasse 91, Erlangen 92054, Germany.
The term "aerophilic surface" is used to describe superhydrophobic surfaces in the Cassie-Baxter wetting state that can trap air underwater. To create aerophilic surfaces, it is essential to achieve a synergy between a low surface energy coating and substrate surface roughness. While a variety of techniques have been established to create surface roughness, the development of rapid, scalable, low-cost, waste-free, efficient, and substrate-geometry-independent processes for depositing low surface energy coatings remains a challenge.
View Article and Find Full Text PDFArresting of efflorescence in ceramic tiles developed using caustic alumina industry waste (red mud).
Sci Total Environ
January 2025
CSIR-Advanced Materials and Processes Research Institute (CSIR-AMPRI), Bhopal, Madhya Pradesh, India; Academy of Scientific and Innovative Research (AcSIR), Ghaziabad, India. Electronic address:
Conversion of caustic red mud (RM, Alumina industry waste) into building materials becoming one of the viable solution for its large scale utilization. The building materials developed using RM often results in efflorescence due to its high alkalinity, which is detrimental for the structural integrity of the buildings. The X-ray shielding tiles developed through ceramic route using the mixtures of RM, BaSO and kaolin clay also suffers from severe NaSO efflorescence when sintered above 1000 °C.
View Article and Find Full Text PDFSustainability in Construction: Geopolymerized Coating Bricks Made with Ceramic Waste.
Materials (Basel)
December 2024
Department of Architectural Construction and Technology, Universidad Politécnica de Madrid, 28040 Madrid, Spain.
Article Synopsis
- Brick waste often occurs due to poor quality in artisanal production, particularly in Ecuador, and this research focuses on repurposing discarded bricks through a process called geopolymerization.
- Using sodium hydroxide as an activator, the research involved characterizing the recycled material's chemical and structural properties, as well as testing its physical and mechanical attributes.
- Findings indicated that the geopolymerized bricks enhance thermal performance in buildings, leading to significant reductions in heating and cooling needs, positioning them as sustainable alternatives to traditional construction materials.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!