Background: Little is known about the effect of the type of splint material, heat-cured PMMA (HC) or chemical-cured PMMA (CC) on the wear of opposing tooth surfaces.
Objective: The aim of this in vitro study was to evaluate two-body wear of dentin, enamel, glass-ceramic or one of four resin composites when opposing splint materials, namely ProBase HC and CC.
Methods: The two-body wear of bovine dentine, bovine enamel, glass-ceramic IPS e.max CAD (EMAX) and four composites (Filtek Z250 [Z250], Clearfil AP-X [AP-X], Clearfil Majesty Posterior [CMP], Filtek Supreme XTE [FSE]) opposing three antagonists (HC and CC and stainless steel as control) were evaluated in the ACTA wear machine. In addition, all the surfaces were evaluated with scanning electron microscopy.
Results: The highest average wear was observed in the case of dentin. The lowest average wear was found EMAX. In every case-except for EMAX-the wear rate was higher with HC than with CC (all differences being statistically significant).
Conclusions: The level of wear of enamel, dentin and various resin composites was higher in contact with HC than in CC, the wear of dentin being the highest. In the case of a patient with no or little tooth wear or whose teeth are restored with composite material or glass-ceramic, the splint HC might be preferred because of its better durability. However, when the splint is in contact with opposing dentin preservation of the dentin, CC might be the best choice.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9291448 | PMC |
| http://dx.doi.org/10.1111/joor.13235 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Cellular Core/Sheath Filaments with Thermoresponsive Vacuum Cavities for Prolonged Passive Temperature-Adaptive Thermoregulation.
Adv Sci (Weinh)
January 2025
School of Fashion and Textiles, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong, 999077, China.
Acting as the interface between the human body and its environment, clothing is indispensable in human thermoregulation and even survival under extreme environmental conditions. Development of clothing textiles with prolonged passive temperature-adaptive thermoregulation without external energy consumption is much needed for protection from thermal stress and energy saving, but very challenging. Here, a temperature-adaptive thermoregulation filament (TATF) consisting of thermoresponsive vacuum cavities formed by the temperature-responsive volume change of the material confined in the cellular cores of the filament is proposed.
View Article and Find Full Text PDFFracture Resistance and Wear Behavior of Ultra-Thin Occlusal Veneers Made From Translucent Zirconia Ceramics Bonded to Different Tooth Substrates.
J Esthet Restor Dent
January 2025
Department of Prosthodontics, Propaedeutics and Dental Materials, School of Dentistry, Christian-Albrechts University at Kiel, Kiel, Germany.
Objective: Investigation of the mechanical properties of occlusal veneers made from zirconia with varying translucency, bonded to different tooth substrates.
Materials And Methods: Sixty-four extracted molars were divided into two groups: preparation within enamel (E) or extending into dentin (D). Veneers were milled from four zirconia ceramics (n = 8): 5Y-TZP (HT), a multilayer of 5 and 3Y-TZP (GT), 3Y-TZP (LT), and 4Y-TZP (MT).
Time-restricted eating (TRE) helps regulate rest-activity rhythms, blood glucose, and other diurnally regulated energetics processes, which may have implications for persistent fatigue. In a randomized controlled trial, we tested the effects of TRE vs. control on fatigue in cancer survivorship.
View Article and Find Full Text PDFCoating Agents for Resin Composites: Effect on Color Stability, Roughness, and Surface Micromorphology Subjected to Brushing Wear.
Oper Dent
January 2025
*Roberta Tarkany Basting, DDS, MSc, PhD, Professor, Restorative Dentistry Department, Faculdade São Leopoldo Mandic, São Paulo, Brazil.
This study evaluated the influence of six resin composite coating agents on color stability and surface roughness after toothbrushing abrasion. Discs (Ø6 mm x 2 mm) of nanofilled resin composite (Filtek Z350XT) were prepared for application of coating agents (n=10): control (absence), two surface sealants (PermaSeal and BisCover LV), two adhesive systems (Scotchbond Multi-Purpose Adhesive/3M Oral Care and Single Bond Universal), and two modeling liquids (Modeling Resin and Composite Wetting Resin). CIELab*, WID, and color change (ΔEab, ΔE00, and ΔWID) were analyzed at baseline, after finishing and polishing, after application of coating agents, after coffee staining (simulating 30 days and one year of staining), and after toothbrushing abrasion.
View Article and Find Full Text PDFMicrostructural Assessment of Molybdenum Disulfide Coatings Using Nanoindentation Hardness.
ACS Appl Mater Interfaces
January 2025
Material, Physical and Chemical Sciences Center, Sandia National Laboratories, Albuquerque, New Mexico 87123, United States.
MoS coatings are used extensively in aerospace and defense applications due to their ultralow friction and high wear resistance. Burnished and resin-bonded MoS coatings are commonly used in these applications due to simplicity in deposition and history of use, despite issues with consistency in coating properties and performance. Physical vapor deposition (PVD) of MoS thin films has emerged as a process alternative in the past 50 years, promising far greater control over film structure and composition but at a greater cost.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!