In this article, 2000 PPI red silicon-based AlGaInP micro-LED arrays were fabricated and investigated. The AlGaInP epilayer was transferred onto the silicon substrate via the In-Ag bonding technique and an epilayer lift-off process. The silicon substrate with a high thermal conductivity could provide satisfactory heat dissipation, leading to micro-LED arrays that had a stable emission spectrum with increasing current density from 20 to 420 A/cm along with a red-shift of the peak position from 624.69 to 627.12 nm ( = 2.43 nm). Additionally, increasing the injection current density had little effect on the CIE (x, y) of the micro-LED arrays. Further, the I-V characteristics and light output power of micro-LED arrays with different pixel sizes demonstrated that the AlGaInP red micro-LED array on a silicon substrate had excellent electrical stability and optical output.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1364/OE.428482 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
A bright future for micro-LED displays.
Light Sci Appl
December 2024
Research Center for Materials, Architectures and Integration of Nanomembranes (MAIN), Chemnitz University of Technology, Chemnitz, Germany.
The development of GaN-based Micro-LED arrays achieving brightnesses exceeding 10 nits and high-density micro-displays with up to 1080×780 pixels marks a true breakthrough in the field. This breakthrough is a result of mastering a combination of long-standing challenges comprising wafer-scale high-quality epitaxial growth, sidewall passivation, efficient photon extraction, and elegant bonding technologies, and promises significant advantages for augmented and virtual reality devices, wearables, and next-generation consumer electronics.
View Article and Find Full Text PDFIn this study, we explored the size-dependent optoelectronic characteristics of InGaN/GaN red micro-LEDs grown on Si substrates. We successfully demonstrated the fabrication of 4-inch wafer-scale InGaN/GaN micro-LEDs, showcasing the feasibility of large-scale production. Additionally, we presented the binary pixel display with 6 µm pitch, achieving a resolution of 4232 PPI.
View Article and Find Full Text PDFHere, we demonstrate replacing opaque Cr/Pt/Au metal p-electrodes with transparent indium tin oxide (ITO) p-electrodes to increase the light output of InGaN-based micro-light-emitting diodes (micro-LEDs). ITO p-electrodes exhibit high transmittance of ∼ 80% across the visible spectrum and low resistivity, while metal p-electrodes exhibit negligible transmittance and significant absorption. The 20 × 20 µm and 50 × 50 µm green micro-LED arrays with ITO p-electrodes yield 1.
View Article and Find Full Text PDFWhat we believe to be a novel fabrication process for monolithic full-color (RGB) micro-LED (µLED) display technology, featuring three-dimensional (3D) and quantum dot (QD)-based color conversion layer, has been proposed. This method offers advantages such as a wide color gamut, high pixel density, high yield, and low cost. A 16 × 16 passive matrix (PM) RGB µLED array, with a pitch size of 80 µm and a pixel density of 328 pixels per inch (PPI), has been successfully realized using flip-chip bonding technology.
View Article and Find Full Text PDFContinuous wave laser fabrication of small pitch/size perovskite pixels realizes high-resolution color conversion micro-LED displays.
Nanoscale
October 2024
MIIT Key Laboratory of Advanced Display Materials and Devices, Jiangsu Engineering Research Center for Quantum Dot Display, School of Materials Science and Engineering, Institute of Optoelectronics & Nanomaterials, Nanjing University of Science and Technology, Nanjing 210094, China.
As a new generation of display technology, micro-light-emitting diodes (micro-LEDs) have been widely recognized owing to their excellent performance in brightness, contrast ratio, resolution, . This work proposes a continuous wave (CW) laser writing strategy to achieve perovskite quantum dots (PQDs) array with small pixel size and pitch, overcoming the processing difficulties and limitations of mass transfer. Since PQDs have highly dynamic surface ligand states and low ionic bond energy, suitable laser power can quench PQDs and form an array area.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!