The 2019 Ridgecrest, California seismic sequence, including an Mw6.4 foreshock and Mw7.1 mainshock, represent the largest regional seismic events within the past 20 years. To obtain accurate coseismic fault-slip distribution, we used precise positioning data of small earthquakes from January 2019 to October 2020 to determine the dip parameters of the eight fault geometry, and used the Interferometric Synthetic Aperture Radar (InSAR) data processed by Xu et al. (Seismol Res Lett 91(4):1979-1985, 2020) at UCSD to constrain inversion of the fault-slip distribution of both earthquakes. The results showed that all faults were sinistral strike-slips with minor dip-slip components, exception for dextral strike-slip fault F2. Fault-slip mainly occurred at depths of 0-12 km, with a maximum slip of 3.0 m. The F1 fault contained two slip peaks located at 2 km of fault S4 and 6 km of fault S5 depth, the latter being located directly above the Mw7.1hypocenter. Two slip peaks with maximum slip of 1.5 m located 8 and 20 km from the SW endpoint of the F2 fault were also identified, and the latter corresponds to the Mw6.4 earthquake. We also analyzed the influence of different inversion parameters on the fault slip distribution, and found that the slip momentum smoothing condition was more suitable for the inversion of the earthquakes slip distribution than the stress-drop smoothing condition.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8270957PMC
http://dx.doi.org/10.1038/s41598-021-93521-0DOI Listing

Publication Analysis

Top Keywords

fault-slip distribution
12
coseismic fault-slip
8
2019 ridgecrest
8
parameters fault
8
maximum slip
8
slip peaks
8
slip distribution
8
smoothing condition
8
fault
7
slip
7

Similar Publications

Seismic response of mountain tunnel induced by fault slip.

Sci Rep

August 2024

Quality Supervision Station, Joint Logistics Support Force Engineering, PLA, Nanjing, China.

With the rapid development of Chinese transportation networks, such as the Sichuan-Tibet railway, numerous tunnels are under construction or planned in mountainous regions. Some of these tunnels must traverse or be situated near active fault zones, which could suffer damage from fault slip. In this study, the seismic response of a mountain tunnel subjected to coseismic faulting was analyzed using a fault-structure system in a two-step process.

View Article and Find Full Text PDF

In Geophysics, topographic factors are observations that can be directly measured, but they are often ignored to simplify the model. Studying the coseismic deformation caused by earthquakes helps accurately determine the epicenter's parameterization. It provides a reference for the reasonable layout of coseismic observation stations and GNSS observation stations.

View Article and Find Full Text PDF

Fault roughness controls injection-induced seismicity.

Proc Natl Acad Sci U S A

January 2024

Helmholtz Centre Potsdam, GFZ German Research Centre for Geosciences, Geomechanics and Scientific Drilling, Potsdam 14473, Germany.

Surface roughness ubiquitously prevails in natural faults across various length scales. Despite extensive studies highlighting the important role of fault geometry in the dynamics of tectonic earthquakes, whether and how fault roughness affects fluid-induced seismicity remains elusive. Here, we investigate the effects of fault geometry and stress heterogeneity on fluid-induced fault slip and associated seismicity characteristics using laboratory experiments and numerical modeling.

View Article and Find Full Text PDF

Research on the Surface Deformation, Fault Rupture, and Coseismic Geohazard of the 2022 Luding Mw 6.8 Earthquake.

Sensors (Basel)

December 2023

State Key Laboratory of Geohazard Prevention and Geoenvironment Protection, Chengdu University of Technology, Chengdu 610059, China.

An Mw 6.8 earthquake occurred in Luding County, Ganzi Tibetan Autonomous Prefecture, Sichuan Province, on 5 September 2022. This seismic event triggered numerous coseismic geohazards in the seismic zone.

View Article and Find Full Text PDF

The mechanical properties of soil in fault-fracture zone areas are diverse and complex. Deep excavation projects often encounter adverse geological conditions such as reverse faulting, which can lead to surface subsidence and collapses, posing significant challenges to excavation safety. Currently, there is limited research in the field of deep excavation engineering that analyzes the influence of reverse faulting on the deformation of retaining piles, and the existing research methods are not systematic enough.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!