Recent advances highlight the potential of photopolymerizable allylated gelatin (GelAGE) as a versatile hydrogel with highly tailorable properties. It is, however, unknown how different photoinitiating system affects the stability, gelation kinetics and curing depth of GelAGE. In this study, sol fraction, mass swelling ratio, mechanical properties, rheological properties, and curing depth were evaluated as a function of time with three photo-initiating systems: Irgacure 2959 (Ig2959; 320-500 nm), lithium phenyl-2,4,6-trimethylbenzoylphosphinate (LAP; 320-500 nm), and ruthenium/sodium persulfate (Ru/SPS; 400-500 nm). Results demonstrated that GelAGE precursory solutions mixed with either Ig2959 or LAP remained stable over time while the Ru/SPS system enabled the onset of controllable redox polymerization without irradiation during pre-incubation. Photo-polymerization using the Ru/SPS system was significantly faster (<5 s) compared to both Ig2959 (70 s) and LAP (50 s). Plus, The Ru/SPS system was capable of polymerizing a thick construct (8.88 ± 0.94 mm), while Ig2959 (1.62 ± 0.49 mm) initiated hydrogels displayed poor penetration depth with LAP (7.38 ± 2.13 mm) in between. These results thus support the use of the visible light based Ru/SPS photo-initiator for constructs requiring rapid gelation and a good curing depth while Ig2959 or LAP can be applied for photo-polymerization of GelAGE materials requiring long-term incubation prior to application if UV is not a concern.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8201352 | PMC |
| http://dx.doi.org/10.3390/polym13111877 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
[Clinical dilemma and indication selection of restoration for permanent tooth defects in adolescents].
Beijing Da Xue Xue Bao Yi Xue Ban
February 2025
Department of Prosthodontics, Peking University School and Hospital of Stomatology & National Center for Stomatology & National Clinical Research Center for Oral Diseases & National Engineering Research Center of Oral Biomaterials and Digital Medical Devices & Beijing Key Laboratory of Digital Stomatology, Beijing 100081, China.
Adolescence is defined as a population ranging from ten to nineteen years old. Permanent teeth in adolescents are of critical significance as they are actively involved in mastication, contribute to aesthetic appearance, play a role in pronunciation, and are integral to the growth and development of the stomatognathic system. Specifically, permanent teeth in adolescents comprise those with incomplete root development and those with complete root development but unstable gingival margin positions.
View Article and Find Full Text PDF[Therapeutic effect of concentrated growth factors combined with self-curing calcium phosphate cement on periodontal intrabony defects: Clinical and radiographic evaluation].
Beijing Da Xue Xue Bao Yi Xue Ban
February 2025
First Clinical Division, Peking University School and Hospital of Stomatology & National Center for Stomatology & National Clinical Research Center for Oral Diseases & National Enginee-ring Research Center of Oral Biomaterials and Digital Medical Devices, Beijing 100081, China.
Objective: To clarify the role of concentrated growth factors (CGF) in the treatment of periodontal cement defects using calcium phosphate cement (CPC) with self-curing properties.
Methods: Thirty-six intrabony defects were randomly divided into two groups. The experimental group received CGF+CPC treatment (=18), while the control group received CPC treatment alone (=18).
Purpose: To make micro-CT comparison and evaluation of sealant penetration depth in different types of fissures after heating of the material or application of vibrations.
Materials And Methods: One hundred sound third molars have been sealed as follows: group 1 (n = 20), light-cured resin sealant at room temperature, group 2 (n = 20), light-cured resin sealant, preheated to 41.0°C, group 3 (n = 20), light-cured resin sealant, preheated to 51.
Vat Photopolymerization Additive Manufacturing of WC-Co Hardmetals Enabled by In Situ Polymerization-Induced Microencapsulation.
ACS Appl Mater Interfaces
January 2025
State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China.
The additive manufacturing of hardmetals has attracted great attention recently but faces significant challenges in low printing resolution and low mechanical strength. Herein, the fabrication of hardmetal parts with complex structures and high surface quality by vat photopolymerization assisted with a sintering process has been achieved. This was enabled by in situ polymerization-induced microencapsulation of WC powder, which simultaneously enhances the photocuring ability and sedimentation stability of the WC-Co slurry.
View Article and Find Full Text PDFSystematic evaluation of adhesives for implant fixation in multimodal functional brain MRI.
MAGMA
January 2025
Translational Research Imaging Center (TRIC), Clinic of Radiology, University of Münster, Albert-Schweitzer-Campus 1, building A16, 48149, Münster, Germany.
Objective: Invasive multimodal fMRI in rodents is often compromised by susceptibility artifacts from adhesives used to secure cranial implants. We hypothesized that adhesive type, shape, and field strength significantly affect susceptibility artifacts, and systematically evaluated various adhesives.
Materials And Methods: Thirty-one adhesives were applied in constrained/unconstrained geometries and imaged with T2*-weighted EPI at 7.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!