This article describes procedures and some results of the first study of females undergoing 3-day Dry Immersion. The experiment "NAIAD-2020" was carried out at the Institute of Biomedical Problems (Moscow, Russia) with the participation of six healthy women volunteers (age 30.17 ± 5.5 years, height 1.66 ± 0.1 m, weight 62.05 ± 8.4 kg, BMI 22.39 ± 2.2 kg/m) with a natural menstrual cycle. During the study, a standard protocol was used, the same as for men, with a minimum period of time spent outside the immersion bath. Before, during and after Immersion, 22 experiments were carried out aimed at studying the neurophysiological, functional, metabolic and psychophysiological functions of the body, the results of which will be presented in future publications. The total time outside the bath for women did not exceed that for men. Systolic and diastolic pressure did not significantly change during the immersion. In the first 24 h after the end of the immersion, heart rate was significantly higher than the background values [(4,20) = 14.67; < 0.0001]. Changes in body temperature and water balance were consistent with the patterns found in men. No significant changes in height and weight were found during immersion. All women reported general discomfort and pain in the abdomen and back. The results of this study did not find significant risks to women's health and showed the feasibility of using this model of the effects of space flight in women of reproductive age.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8236811PMC
http://dx.doi.org/10.3389/fphys.2021.661959DOI Listing

Publication Analysis

Top Keywords

dry immersion
8
immersion
7
female dry
4
immersion naiad-2020
4
naiad-2020 design
4
design specifics
4
specifics 3-day
4
study
4
3-day study
4
study article
4

Similar Publications

Adsorption Structure and Selectivity of Phenols in Water-Immersed Organomontmorillonite Investigated by Molecular Simulation.

Langmuir

January 2025

Department of Environmental Chemistry and Chemical Engineering, School of Advanced Engineering, Kogakuin University, 2665-1 Nakano, Tokyo, Hachioji 192-0015, Japan.

The two-dimensional interlayer space of layered materials has been highlighted due to their adsorption property, whose nanostructure in the water-immersed state is scarcely understood by experiment. Recent developments in molecular simulation have enabled researchers to investigate the interlayer structure, but water content is necessary for accurate modeling. In the present study, we proposed a theoretical method to estimate the saturated water content and adsorption selectivity of trichlorophenol and phenol in montmorillonite modified with hexadecyltrimethylammonium ions.

View Article and Find Full Text PDF

Effect of post-processing on the surface, optical, mechanical, and dimensional properties of 3D-printed orthodontic clear retainers.

Clin Oral Investig

January 2025

School of Materials Science and Innovation, Faculty of Science, Mahidol University, Phuttamonthon 4 Road, Salaya, Phuttamonthon District, Nakhon Pathom, 73170, Thailand.

Objectives: To address the high surface roughness and poor optical properties of three-dimensional (3D) printed orthodontic clear retainers, an alternative post-processing protocol was investigated with the goal of achieving improved surface, optical, and mechanical properties while preserving dimensional accuracy.

Materials And Methods: Samples were prepared from two biocompatible methacrylate-based 3D-printing resins (Formlabs Dental LT Clear V2, NextDent OrthoFlex) and one thermoplastic material (Duran). For the 3D-printed resins, one group was post-processed by rinsing in isopropyl alcohol, while another group was centrifuged before post-curing in glycerine.

View Article and Find Full Text PDF

Rain cracking compromises quality and quantity of sweet cherries worldwide. Cracking susceptibility differs among genotypes. The objective was to (1) phenotype the progeny of a cross between a tolerant and a susceptible sweet cherry cultivar for cuticle mass per unit area, strain release on cuticle isolation, cuticular microcracking and calcium/dry mass ratio and (2) relate these characteristics to cracking susceptibilities evaluated in laboratory immersion assays and published multiyear field observations.

View Article and Find Full Text PDF

Dataset of some added-lignin thermoformed pulps.

Data Brief

December 2024

RISE PFI AS, Høgskoleringen 6B, 7491 Trondheim, Norway.

This data article summarizes the material properties of some added-lignin thermoformed pulps (ALTPs). This type of molded pulp is particularly suited for replacing plastics in environments, where moisture is encountered, as the lignin reduces the transport and adsorption of water. The dataset was measured on wet formed substrates with either softwood chemi-thermomechanical pulp (CTMP) or northern bleached softwood Kraft pulp (NBSK).

View Article and Find Full Text PDF

Introduction: This study investigated the physical, mechanical, and optical properties of 3-dimensional (3D) printing resins compared with thermoplastic materials to evaluate their suitability for the fabrication of orthodontic clear retainers.

Methods: Samples were prepared from thermoplastic sheets (Duran [Scheu-Dental GmbH, Iserlohn, Germany] and Zendura [Bay Materials LLC, Fremont, Calif]) and biocompatible 3D-printing resins (Dental LT Clear V2 [Formlabs Inc, Somerville, Mass] and OrthoFlex [Nextdent BV, Soesterberg, The Netherlands]) according to the manufacturer's instructions. The materials were characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, and water sorption tests.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!