Catfacing and gummosis/sap-type injury associated with a heteropteran pest complex were sampled at five peach orchards in southern Florida during two consecutive growing seasons. Trapping and visual surveys indicate that Euschistus servuis (Say) (Hemiptera: Pentatomidae) was the dominant heteropteran pest in the study orchards. The spatial arrangement of injury indicated a random distribution, as determined by Taylor's power law. Spatial analysis by distance indices indicated a random arrangement of fruit injury in a majority of the sample site × date combinations and analysis of local clustering did not provide evidence of patches of fruit injury occurring near orchard borders. The coefficients from Taylor's power law were used to develop sequential sampling plans based on hypothetical injury thresholds. Sequential sampling plans were compared to a simple random sample of 15 sample units using a simulation approach. The sequential sampling plan was able to achieve equivalent levels of accuracy when compared to the 15-unit fixed sampling plan while reducing the number of sample units required to an average of 7.99. The sequential sampling plans developed in this study are an improvement over simple random sampling; however, further research is needed to determine how to best implement sequential sampling of fruit injury in Florida peach orchards to better inform management decisions.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1093/jee/toab106 | DOI Listing |
Clin Trials
January 2025
Department of Biostatistics, University of Florida, Gainesville, FL, USA.
Introduction: The sequential parallel comparison design has emerged as a valuable tool in clinical trials with high placebo response rates. To further enhance its efficiency and effectiveness, adaptive strategies, such as sample size adjustment and allocation ratio modification can be employed.
Methods: We compared the performance of Jennison and Turnbull's method and the Promising Zone approach for sample size adjustment in a two-phase sequential parallel comparison design study.
Sensors (Basel)
January 2025
Department of Industrial Engineering and Mathematical Sciences, Università Politecnica delle Marche, 60131 Ancona, Italy.
The effective knowledge of emissivity is pivotal to obtain reliable temperature measurements through non-contact techniques like pyrometry and thermal imaging. This is fundamental in high-temperature applications since material emissivity strongly depends on temperature conditions. Given the recent attention in high-temperature applications, especially for replacing fossil-fuel-dependent heating with greener solutions in energy-intensive processes, renewed interest in characterizing materials radiant properties rose.
View Article and Find Full Text PDFSensors (Basel)
January 2025
Instituto de Engenharia de Sistemas e Computadores-Microsistemas e Nanotecnologias (INESC-MN), Rua Alves Redol, 1000-029 Lisbon, Portugal.
Point-of-care (PoC) devices offer a promising solution for fast, portable, and easy-to-use diagnostics. These characteristics are particularly relevant in agrifood fields like viticulture where the early detection of plant stresses is crucial to crop yield. Microfluidics, with its low reagent volume requirements, is well-suited for such applications.
View Article and Find Full Text PDFSensors (Basel)
January 2025
School of Mathematics and Information Science, Guangxi University, Nanning 530004, China.
In this paper, a novel particle filter based on one-step smoothing is proposed for nonlinear systems with random one-step delay and missing measurements. Such problems are commonly encountered in networked control systems, where random one-step delay and missing measurements significantly increase the difficulty of dynamic state estimation. The particle filter is a nonlinear filtering method based on sequential Monte Carlo sampling.
View Article and Find Full Text PDFMaterials (Basel)
January 2025
Life Sciences Division, National Research Council of Canada, 75 de Mortagne Boulevard, Boucherville, QC J4B 6Y4, Canada.
A novel approach to protein quantification utilizing a microfluidic platform activated by a magnetic assembly of functionalized magnetic beads around soft magnetic capture centers is presented. Functionalized magnetic beads, known for their high surface area and facile manipulation under external magnetic fields, are injected inside microfluidic channels and immobilized magnetically on the surface of glass-coated soft magnetic microwires placed along the symmetry axis of these channels. A fluorescent (Cy5) immunomagnetic sandwich ELISA is then performed by sequentially flowing the sample and all necessary reagents in the microfluidic channels.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!