The process of water-based foaming of bitumen produces binders that can be incorporated in cold recycled asphalt mixes and pavement upper structural layers made of half-warm mix asphalt prepared at 100-130 °C. During the foaming process, cold water and air act on hot bitumen (160-170 °C), which results in the explosive vaporization of water leading to changes in the binder structure. The impact of foaming on the properties of bitumen 70/100 was evaluated by investigating the binder characteristics before and after foaming. Determination of two foaming parameters, maximum expansion and half-life, was followed by measurements of penetration at 25 °C, softening point, Fraass breaking point, and dynamic viscosity at 60, 90, and 135 °C. Rheological and low-temperature tests were also performed before and after foaming bitumen 70/100. The Bending Beam Rheometer method was applied to determine the low temperature stiffness modulus. A DHR-2 rheometer was used to determine the dynamic modulus and phase angle of the tested binder. The Black and master curves before and after foaming were plotted in the 2S2P1D model and the model parameters were analysed. Analysis of the test results confirmed the effects of the foaming process on the basic, low-temperature, and rheological characteristics of the bitumen.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8197502 | PMC |
| http://dx.doi.org/10.3390/ma14112803 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Foaming purees as a strategy to modify oral processing time.
Curr Res Food Sci
December 2024
Institute of Agrochemistry and Food Technology (IATA, CSIC), Spain.
Food structure modification by increasing viscosity or adding heterogeneity to the food product has shown to effectively change food oral processing. In this study, it was hypothesized that the addition of gas to purees could affect oral processing. This was achieved by creating different structures in purees using a gas syphon, vacuum and syphon + vacuum.
View Article and Find Full Text PDFHierarchical Biogenic-Based Thermal Insulation Foam.
ACS Nano
January 2025
Department of Materials Science and Engineering, University of Maryland, College Park, Maryland 20742, United States.
Biogenic-based foam, renowned for its sustainable and eco-friendly properties, is emerging as a promising thermal insulating material with the potential to significantly enhance energy efficiency and sustainability in building applications. However, its relatively high thermal conductivity, large-pore configurations, and energy-intensive manufacturing processes hinder its widespread use. Here, we report on the scalable, one-pot synthesis of biogenic foams achieved by integrating recycled paper pulp and in situ nanoporous silica formation, resulting in a hierarchical structure comprising both micropores and nanopores.
View Article and Find Full Text PDFSynthesis of Highly Expandable Poly(methacrylimide) (PMI) Precursor Beads Through Optimized Suspension Polymerization of MAA-MAN-tBMA Copolymers.
Polymers (Basel)
December 2024
School of Chemistry and Chemical Engineering, Northwestern Polytechnical University, Xi'an 710072, China.
Bead-foaming technology effectively addresses production cycles, polymerization control, and cellular structure defects in conventional bulk foaming, especially in high-performance PMI foams. In this work, highly expandable PMI beads were synthesized based on the aqueous suspension polymerization of methacrylic acid-methacrylonitrile-tert-butyl methacrylate (MAA-MAN-tBMA) copolymers. The suspension polymerization was stabilized by reducing the solubility of MAA by the salting-out effect and replacing formamide (a common PMI foaming agent) with tBMA.
View Article and Find Full Text PDFPolypropylene Modified with Polyethylene Through Reactive Melt Blending: Fabrication and Characterizations.
Polymers (Basel)
December 2024
Department of Chemical Engineering, Hanyang University, Ansan 15588, Republic of Korea.
Conventional PP with a linear chain structure is not suitable for foam processing due to its poor rheological properties. In this study, PP was modified with PE through reactive melt blending of maleic anhydride-grafted PP (MA-PP) with a small amount of PE bearing glycidyl groups on its backbone (G-PE), with the aim of enhancing the melt rheological properties of PP to make it suitable for foam processing. An anhydride-epoxy reaction occurred between MA-PP and G-PE during the melt processing, resulting in the formation of a crosslinked polymer network, which was confirmed by FTIR spectroscopy, a solubility test, and the presence of a rubbery plateau above the melting point.
View Article and Find Full Text PDFPreliminary Data of the Nutritive, Antioxidative, and Functional Properties of Watermelon ( L.) Flour and Seed Protein Concentrate.
Molecules
January 2025
Department of Food Storage and Technology, Wroclaw University of Environmental and Life Sciences, 37 Chelmonskiego Street, 51-630 Wroclaw, Poland.
The growing interest in a plant-based diet leads to the search for new sources of protein in the human diet as an alternative to animal proteins. Plant materials that can supplement protein as additives in food products are being studied. Watermelon seeds ( L.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!