The intimate relationship between the mandibular canal (MC) and the first mandibular molar tooth presents challenges when performing dentoalveolar surgical procedures due to the probability of causing iatrogenic injury to the inferior alveolar neurovascular bundle. Superimposition between the MC and the first molar (M1) tooth roots is often observed on intraoral dental radiographs in small breed dogs. However, due to the radiograph's bidimensional nature, it is impossible to determine the buccal or lingual localization of the first molar roots with respect to the MC. Thus, this study's objective was to determine the localization of the first molar tooth's roots in relation to the position of the MC and their overlapping percentage with the canal in small-bodyweight dogs (<15 kg) using tomographic diagnostic images. For this, cone-beam computed tomography and high-definition computed tomography exams from 103 small breed dogs (under 15 kg) were retrospectively assessed to determine the lingual or buccal localization of the first molar tooth's roots with respect to the MC and the degree of overlap of the roots with the canal. In conclusion, most of the roots of M1 of dogs under 15 kg were located at the MC's lingual aspect (82.7%) with an overall superimposition median with the MC of 100 and 90% for the mesial and distal roots, respectively. Straddle tooth roots were not a common anatomical presentation in the dogs of this study.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8149890PMC
http://dx.doi.org/10.3389/fvets.2021.684763DOI Listing

Publication Analysis

Top Keywords

mandibular molar
8
molar roots
8
relationship mandibular
8
mandibular canal
8
small breed
8
molar tooth
8
localization molar
8
molar
5
localization mandibular
4
roots
4

Similar Publications

Introduction: This randomized clinical trial compared arch dimensional changes, dentoskeletal changes, and the rate of overbite correction in deep bite adults treated with fixed appliances and either maxillary incisor bite turbos (IBT) or canine bite turbos (CBT).

Materials And Methods: Forty-six deep bite subjects treated with fixed appliances were randomized into IBT (n = 23) and CBT (n = 23) groups. Changes in intercanine width (ICW), arch height (AH), and Little's Irregularity Index (LII) were analyzed from before treatment (T) to 3 months after aligning with 0.

View Article and Find Full Text PDF

Teeth, either erupted or impacted, that exceed the normal count are known as supernumerary teeth. They can appear unilaterally or bilaterally, singly or in multiples, and may be located anywhere in both dental arches. Multiple permanent impacted supernumerary teeth are uncommon and are often associated to syndromes but can be idiopathic.

View Article and Find Full Text PDF

Superior effect of mini-implant anchorage in the treatment of skeletal class II malocclusion.

J Orthod Sci

November 2024

Department of Orthodontics and Pedodontics, Faculty of Dentistry, Van Lang University, Binh Thanh District, Ho Chi Minh City, Vietnam.

Objectives: To evaluate the effectiveness of mini-implant (MI) anchorage versus conventional anchorage for the treatment of skeletal class II malocclusion.

Materials And Methods: The study was conducted on 64 patients with skeletal class II malocclusion. The patients were divided into two groups: 1) 32 patients underwent conventional anchorage, and 2) 32 patients underwent MI anchorage.

View Article and Find Full Text PDF

Investigating the characteristics of the mandibular canal in cone beam CT.

J Orthod Sci

November 2024

Department of Pediatrics Dentistry and Orthodontics, Faculty of Odonto-Stomatology, Can Tho University of Medicine and Pharmacy, Can Tho City, Vietnam.

Context: The mandibular canal (MC) is an essential landmark that should be considered before any surgeries. Therefore, accurately assessing the location and characteristics of the MC in cone beam computed tomography (CBCT) imaging is very important.

Aims: To determine the characteristics of the MC in relation to adjacent anatomical structures in CBCT projections.

View Article and Find Full Text PDF

Purpose: To determine the effect of wall thickness on the fracture load of hollow-structured zirconia teeth fabricated using 3D printing.

Methods: The geometry of an artificial ceramic tooth (mandibular right first molar) was copied and modified. The final test group design yielded wall thicknesses of 0.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!