AI Article Synopsis

  • The study investigated how different endodontic irrigation solutions and sealing dentin surfaces before irrigation affect the fracture strength of maxillary premolars.
  • Seventy-two human maxillary premolars were divided into six groups to assess varying treatment methods and the impact of sealing before irrigation.
  • Results indicated that the unrestored and conventionally restored groups had the lowest fracture strength, while the presealed group showed the highest fracture strength, highlighting the importance of sealing in enhancing tooth durability post-treatment.

Article Abstract

This in vitro study aimed to evaluate the influence of endodontic irrigation solutions and resin sealing of the dentin surfaces of the cavity before irrigation on the fracture strength (FS) of maxillary premolars. Seventy-two human maxillary premolars were randomly assigned to 6 groups (n = 12). Group 1 consisted of intact teeth that served as negative controls. In groups 2 to 6, root canal treatment was performed after mesio-occlusal preparation. In group 6, the dentin surfaces of the mesio-occlusal cavity were sealed with a self-adhesive flowable composite resin before instrumentation and irrigation of the canal. The volume and contact time of the irrigation solutions used during endodontic treatment of groups 2, 4, 5, and 6 were standardized as follows: 2 mL of 5.25% sodium hypochlorite (NaOCl) for 1 minute after each file, 5 mL of 17% ethylenediaminetetraacetic acid (EDTA) for 3 minutes after instrumentation was completed, and 5 mL of 5.25% NaOCl for 1 minute as the final irrigation. In group 3, the irrigation solution was normal saline solution only. After root canal obturation, in group 2, the cavities were left unrestored as a positive control. In groups 3 (saline-rinsed), 4 (conventionally restored), and 6 (presealed), the restorations were carried out with an etch-and-rinse adhesive and composite resin immediately after root canal obturations. In group 5 (delay-restored), the restorations were carried out with an etch-and-rinse adhesive and composite resin after a 1-week delay. After thermomechanical cycling, the teeth were subjected to FS testing under continuous compressive force. Data were analyzed with 1-way analysis of variance and Tukey tests. The unrestored group, which demonstrated the lowest FS, did not differ significantly from the conventionally restored group; the FS of both groups was significantly lower than that in the other groups (P ≤ 0.001). The presealed group exhibited the highest FS (P ≤ 0.02). The FS values of the saline and delay-restored groups were statistically comparable. In the present study, NaOCl/EDTA irrigation had an adverse effect on the FS. Presealing of the dentin surfaces of the cavity with self-adhesive flowable composite resin significantly increased the FS of aged composite resin-restored premolars.

Download full-text PDF

Source

Publication Analysis

Top Keywords

composite resin
16
maxillary premolars
12
dentin surfaces
12
root canal
12
fracture strength
8
irrigation solutions
8
surfaces cavity
8
group
8
self-adhesive flowable
8
flowable composite
8

Similar Publications

Research of mesoporous silica loaded lignin to enhance the anti-corrosion and anti-weathering performance of epoxy surface.

Int J Biol Macromol

January 2025

Key Laboratory of Automobile Materials, Ministry of Education, and College of Materials Science and Engineering, Jilin University, Changchun 130025, China. Electronic address:

A new type of filler was added to epoxy resin to prepare a composite coating with excellent corrosion and weathering resistance. The simple synthesis process and nonpolluting raw materials of this filler contribute to the development of green chemistry. Specifically, lignin was encapsulated in mesoporous silica, the synergistic effect between the two resulted in the formation of lignin/mesoporous silica composite particles (MSN-L) with excellent ultraviolet (UV) resistance.

View Article and Find Full Text PDF

3-Dimensional topographic enamel surface changes after different debonding techniques for aligner attachments: a micro-CT study.

Clin Oral Investig

January 2025

Faculty of Dentistry, Department of Orthodontics , Hacettepe University, Sihhiye, Ankara, 06100, Turkey.

Introduction: To evaluate topographic changes of enamel surface in 3-dimensional after different debonding methods of aligner attachments formed with 2 different composite resins.

Methods: Vertical rectangular attachments were created on 88 premolar teeth and divided into two composite resin groups (Group 1:flowable, Group 2:packable) (N = 44). These were then divided into two subgroups (N = 22) using different debonding methods.

View Article and Find Full Text PDF

Vat photopolymerization (VPP) is an additive manufacturing method that requires the design of photocurable resins to act as feedstock and binder for the printing of parts, both monolithic and composite. The design of a suitable photoresin is costly and time-consuming. The development of one formulation requires the consumption of kilograms of costly materials, weeks of printing and performance testing, as well as the need to have developers with the expertise and knowledge of the materials used, making the development process cost thousands.

View Article and Find Full Text PDF

The objective of the present work was to prepare hybrid epoxy composites with improved mechanical and thermal properties. The simultaneous use of two different modifiers in an epoxy resin was motivated by the expected occurrence of synergistic effects on the performance properties of the matrix. Such a hybrid composite can be used in more severe conditions and/or in broader application areas.

View Article and Find Full Text PDF

In this paper, alumina-modified wood liquefaction (AL-WP) was prepared by blending nano-alumina (AlO) into wood liquefaction phenolic resin (WP) using a co-blending method. Alumina-modified wood liquefaction protofilament fiber (AL-WPF) was obtained by melt-spinning, curing, and thermo-curing processes, which were followed by carbonization to obtain alumina-modified wood liquefaction carbon fiber (AL-WCF). This paper focuses on the enhancement effect of nano-alumina doping on the mechanical properties and heat resistance of wood liquefaction carbon fiber (WCF), explores the evolution of graphite microcrystalline structure during the high-temperature carbonization process, and optimizes the curing conditions of AL-WPF.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!