An integrated after-treatment device model was established for our target engine based on the fluid simulation software (Converge), and simulation was performed to determine the NH, temperature, and velocity uniformity at the front-end cross section of its SCR catalyst, urea deposition rate, liquid film mass of the mixer, and its positions under a low-load condition. Moreover, the structure of the mixer and injection pressure were optimized to improve the uniformity and reduce the liquid film mass. Our simulation results show the following facts: the liquid film is easily accumulated under a low-load condition and the structure of the mixer and the injection pressure significantly affect the urea deposition rate and uniformities and accumulation masses of the liquid film. As a result, our final optimization results indicate that the mass of the NH and the NH uniformity at the front-end cross section of the SCR catalyst increase by 2.83 times and 5.65%. The urea deposition rate and the cumulative mass of the liquid film fall by 4.82 and 10.4%, respectively. This study has certain theoretical guiding significance for the optimal design of this type of after-treatment devices.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC7970487 | PMC |
| http://dx.doi.org/10.1021/acsomega.0c05785 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Characteristics of Tylvalosin Tartrate Enteric Amorphous Pellets Prepared by Liquid Layering.
Pharm Res
January 2025
Department of Pharmaceutics Science, Shenyang Pharmaceutical University, Shenyang, 110016, China.
Purpose: Tylvalosin Tartrate (TAT), a new-generation macrolide antibiotic, undergoes significant degradation in the stomach and in vivo rapid elimination upon oral administration, resulting in poor bioavailability. This study developed TAT enteric amorphous pellets by liquid layering (TAT/EAP-LL) with pH-sensitive and burst release characteristics, to enhance drug stability in the stomach and concentration enrichment in the duodenum.
Methods: The drug loading layer, isolation layer and enteric layer were formed on the surface of the blank core pellets.
MR imaging of proton beam-induced oxygen depletion.
Med Phys
January 2025
OncoRay - National Center for Radiation Research in Oncology, Faculty of Medicine and University Hospital Carl Gustav Carus, Technische Universität Dresden, Helmholtz-Zentrum Dresden-Rossendorf, Dresden, Germany.
Background: Previous studies have shown that in-beam magnetic resonance imaging (MRI) can be used to visualize a proton beam during the irradiation of liquid-filled phantoms. The beam energy- and current-dependent local image contrast observed in water was identified to be predominantly caused by beam-induced buoyant convection and associated flow effects. Besides this flow dependency, the MR signal change was found to be characterized by a change in the relaxation time of water, hinting at a radiochemical contribution, which was hypothesized to lie in oxygen depletion-evoked relaxation time lengthening.
View Article and Find Full Text PDFBubble coalescence principle in saline water.
Proc Natl Acad Sci U S A
February 2025
School of Chemical Engineering and Technology, China University of Mining and Technology, Xuzhou 221116, China.
Bubbles present in saline water typically exhibit a prolonged lifetime, making them attractive for various engineering processes. Herein, we unveil a transition from delayed bubble coalescence to rapid bursting within about one millisecond in salty solutions. The key aspect in understanding this transition lies in the combined influences of surface deformation and ion surface excess instead of characterizing the ions alone.
View Article and Find Full Text PDFMicrofilm-Formation of High-Viscosity Liquids by Blade Shear Coating.
ACS Omega
January 2025
School of Mechanical Engineering, Dalian University of Technology, Dalian 116024, China.
The distribution of high-viscosity microfilms in designated regions is crucial for the performance and durability of MEMS devices. This paper presents a novel method for controllable film formation in the milli/micron region by blade coating. A microfilm can be formed without viscosity limitation, and the formation process can be monitored only via a one-dimensional force sensor.
View Article and Find Full Text PDFMechanisms of the Photomechanical Response in Thin-Film Dye-Doped Glassy Polymers.
Polymers (Basel)
January 2025
Department of Physics, Washington State University, Pullman, WA 99163, USA.
This work aims to determine the mechanism of the photomechanical response of poly(Methyl methacrylate) polymer doped with the photo-isomerizable dye Disperse Red 1 using the non-isomerizable dye Disperse Orange 11 as a control to isolate photoisomerization. Samples are free-standing thin films with thickness that is small compared with the optical skin depth to assure uniform illumination and photomechanical response throughout their volume, which differentiates these studies from most others. Polarization-dependent measurements of the photomechanical stress response are used to deconvolute the contributions of angular hole burning, molecular reorientation and photothermal heating.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!