Introduction: Type I, flat-wedge and type II, dual-wedge stems are currently two common stem types used in primary, uncemented hip arthroplasty. The prevalence of periprosthetic femur fracture is higher in type I stems, possibly because of the different shapes and areas of bone contact. We aimed to compare the fracture pattern, stem stability during the fracture and type of subsequent procedures in periprosthetic femur fractures between type I and II stems.
Materials And Methods: This was a retrospective, cross-sectional study conducted in a single tertiary referral hospital of Taipei, Taiwan. We included primary hip arthroplasty procedures using type I or type II stems complicated with postoperative periprosthetic femur fractures. We recorded the age, sex, ASA grade, index procedure, institution of where the index procedure was performed, trauma mechanism, time from index procedure to fracture, procedure for periprosthetic fracture and radiographic parameters including Dorr type, Vancouver classification, stem stability, fracture pattern, type and brand of the stems for analysis.
Results: We included 132 patients who had undergone surgery for periprosthetic femur fracture for type I (N = 46) or type II (N = 86) stems. The mean age was 74.5 years and 52.3% of the patients were female. Type I stems were associated with a higher proportion of a complex fracture pattern (52.2% vs. 8.2%), femoral stem loosening (78.2% vs. 60.4%) and a higher rate of revision stem procedures (69.6% vs. 50.0%) compared with type II stems. Using multivariate analysis, type I stem was the only factor for a complex fracture pattern in the overall population (aOR: 23.60, 95% CI: 6.54-85.16), hemiarthroplasty (aOR: 160.50, 95% CI: 9.77-2635.95) and total hip arthroplasty (aOR: 14.17, 95% CI: 2.92-68.79) subgroups.
Conclusion: We observed a difference in fracture patterns between type I and type II stems. Type I stems appear to be an independent risk factor for a complex fracture pattern in patients who had undergone primary hip arthroplasty.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.injury.2021.02.039 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Morphological and clinical study of lateral malleolus fractures based on fracture mapping: a retrospective study.
J Orthop Surg Res
December 2024
Department of Orthopedics and Trauma, Peking University People's Hospital, Beijing, China.
Background: The traditional classification for lateral malleolus fracture has its limitations. In this study, we introduced a three-dimensional (3D) fracture mapping technique using computed tomography (CT) data to assess fracture line distributions and their impact on patient outcomes, offering a refined classification approach.
Methods: Retrospectively, we analysed 97 patients who underwent lateral malleolus fracture surgeries (2014-2019), using CT Digital Imaging and Communications in Medicine data to create 3D models and fracture maps.
Mechanical Deformation Behavior of Polymer Blend Thin Films.
Macromol Rapid Commun
December 2024
School of Materials Engineering, Purdue University, West Lafayette, IN, 47907, USA.
Examining the mechanical properties of polymer thin films is crucial for high-performance applications such as displays, coatings, sensors, and thermal management. It is important to design thin film microstructures that excel in high-demand situations without compromising mechanical integrity. Here, a polymer blend of polystyrene (PS) and polyisoprene (PI) is used as a model to explore microscale deformation behavior under uniaxial mechanical testing.
View Article and Find Full Text PDFA tension system for angular correction of bent intramedullary nails: in vitro analysis.
Eur J Orthop Surg Traumatol
December 2024
Department of Orthopedics and Trauma, Universidade Federal Fluminense (UFF), Niterói, Rio de Janeiro, Brazil.
Purpose: Although several techniques have been described for bent intramedullary nail removal, there is no universally accepted strategy. We hypothesized that a device based on the action principle of a three-point bend fixture could facilitate extraction of bent intramedullary nails; this paper describes its design and experimental testing.
Methods: Five large synthetic left femurs and five steel intramedullary nails were used.
Numerical modelling of interaction of cemented natural fractures and hydraulic fractures.
Sci Rep
December 2024
College of Geology and Environment, Xi'an University of Science and Technology, Xi'an, 710054, Shaanxi, China.
Cemented natural fractures (CNFs) are commonly found in unconventional shale and tight sandstone reservoirs. During the process of hydraulic fracturing, CNFs can affect the propagation of hydraulic fractures and thus impact oil and gas production. However, the interaction behavior between CNFs and hydraulic fractures is still unclear.
View Article and Find Full Text PDFAnalysis on characteristics and mechanism for rock fracture in deep rock with cracks under dynamic-static coupling effect.
Sci Rep
December 2024
School of Civil Engineering and Architecture, Anhui University of Science and Technology, Huainan, 232001, Anhui, China.
The mechanical behavior and fracture mechanisms of deep fractured rocks under explosive dynamic loads are critical for understanding rock instability in engineering applications such as blasting operations. This study aims to investigate how the presence of pre-existing cracks and different stress states affect the mechanical properties and fracture patterns of rock-like specimens under dynamic loading conditions. We utilized a Split Hopkinson Pressure Bar (SHPB) with an active confining pressure loading device to conduct impact compression tests on rock-like specimens containing pre-existing cracks.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!