Rifampicin is one of the key drugs used to treat tuberculosis and is currently used orally. The use of higher oral doses of rifampicin is desired for better therapeutic efficacy, but this is accompanied by increased risk of systemic toxicity thus limiting its recommended oral dose to 10 mg/kg per day. Inhaled delivery of rifampicin is a potential alternative mode of delivery, to achieve high drug concentrations in both the lung and potentially the systemic circulation. In addition, rifampicin exists either as amorphous or crystalline particles, which may show different pharmacokinetic behaviour. However, disposition behaviour of amorphous and crystalline rifampicin formulations after inhaled high-dose delivery is unknown. In this study, rifampicin pharmacokinetics after intra-tracheal administration of carrier-free, amorphous and crystalline powder formulations to Sprague Dawley rats were evaluated. The formulations were administered once daily for seven days by oral, intra-tracheal and oral plus intra-tracheal delivery, and the pharmacokinetics were studied on day 0 and day 6. Intra-tracheal administration of the amorphous formulation resulted in a higher area under the plasma concentration curve (AUC) compared to the crystalline formulation. For both formulations, the intra-tracheal delivery led to significantly higher AUC compared to the oral delivery at the same dose suggesting higher rifampicin bioavailability from the inhaled route. Increasing the intra-tracheal dose resulted in a more than dose proportional AUC suggesting non-linear pharmacokinetics of rifampicin from the inhaled route. Upon repeated administration for seven days, no significant decrease in the AUCs were observed suggesting the absence of rifampicin induced enzyme auto-induction in this study. The present study suggests an advantage of inhaled delivery of rifampicin in achieving higher drug bioavailability compared to the oral route.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1016/j.ejpb.2021.02.011 | DOI Listing |
Angew Chem Int Ed Engl
January 2025
Nanjing Tech University, College of Chemical Engineering, Nanjing, CHINA.
The wide application of zeolite Y in petrochemical industry is well known as one of the milestones in zeolite chemistry and heterogeneous catalysis. However, the traditional organic-free synthesis typically produces (hydro)thermally unstable zeolite Y with Si/Al atomic ratio (SAR) less than 2.5.
View Article and Find Full Text PDFNat Commun
January 2025
School of Environment, Tsinghua University, Beijing, 100084, P. R. China.
Modulation of electronic spin states in cobalt-based catalysts is an effective strategy for molecule activations. Crystalline-amorphous interfaces often exhibit unique catalytic properties due to disruptions of long-range order and alterations in electronic structure. However, the mechanisms of molecule activation and spin states at interfaces remain elusive.
View Article and Find Full Text PDFEur J Pharm Biopharm
January 2025
Department of Pharmaceutical Sciences, Faculty of Pharmacy, Chiang Mai University, Chiang Mai 50200, Thailand; Research Center for Development of Local Lanna Rice and Rice Products, Chiang Mai University, Chiang Mai 50200, Thailand. Electronic address:
The development of a direct compression excipient with extended-release property is crucial for improving tablet manufacturing and drug delivery. This research focuses on developing a novel co-processed excipient composed of rice starch (RS), methylcellulose (MC), and colloidal silicon dioxide (CSD) using a wet granulation technique. The ratios of RS: MC (1.
View Article and Find Full Text PDFPharmaceutics
December 2024
Department of Pharmaceutical Technology and Cosmetology, Faculty of Pharmacy, University of Belgrade, Vojvode Stepe 450, 11221 Belgrade, Serbia.
Background/objectives: Selective laser sintering (SLS) is one of the most promising 3D printing techniques for pharmaceutical applications as it offers numerous advantages, such as suitability to work with already approved pharmaceutical excipients, the elimination of solvents, and the ability to produce fast-dissolving, porous dosage forms with high drug loading. When the powder mixture is exposed to elevated temperatures during SLS printing, the active ingredients can be converted from the crystalline to the amorphous state, which can be used as a strategy to improve the dissolution rate and bioavailability of poorly soluble drugs. This study investigates the potential application of SLS 3D printing for the fabrication of tablets containing the poorly soluble drug carvedilol with the aim of improving the dissolution rate of the drug by forming an amorphous form through the printing process.
View Article and Find Full Text PDFPolymers (Basel)
January 2025
Centre of Molecular and Macromolecular Studies, Polish Academy of Sciences, Sienkiewicza 112, 90-363 Lodz, Poland.
The deformation behavior and instabilities occurring during the drawing of high-density polyethylene (HDPE) were investigated using wide- and small-angle X-ray scattering (WAXS and SAXS) and scanning electron microscopy (SEM) in plain HDPE and paraffin wax- and/or chloroform-modified samples. In contrast to neat HDPE, the modified materials demonstrated strongly suppressed cavitation. However, regardless of cavitation, the tensile deformation of all samples was found to be governed by crystallographic mechanisms active in the crystalline lamellae, supported by shear in the amorphous layers, i.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!