Purpose: To evaluate the effectiveness of nonthermal atmospheric plasma (NTAP) and priming on the shear bond strength (SBS) of a resin cement to two zirconia ceramics after 24 hours and 1 year of water storage.
Materials And Methods: A total of 120 plates (9 x 7 x 2 mm) were obtained from two types of zirconia (Katana, Kuraray Noritake; and ZirCAD, Ivoclar Vivadent) plates randomly divided into 12 groups (n = 10 each). Zirconia ceramic plates were submitted to the following treatments: (1) untreated (control); (2) treated with ZPrime Plus (Bisco Dental) primer; (3) NTAP (Surface Plasma Tool Model SAP, Surface Engineering and Plasma Solution) application for 10 seconds; (4) NTAP for 30 seconds; (5) NTAP for 10 seconds followed by priming; and (6) NTAP for 30 seconds followed by priming. Two silicone molds (2.37-mm diameter x 2-mm height) were positioned on the treated surface of each zirconia plate, and the resin cement (Panavia F 2.0, Kuraray Noritake) was manipulated and inserted into the molds. After light activation, two resin cement cylinders (specimens) were obtained from each plate. One specimen was tested after 24 hours, and the other after 1 year. The shear load was applied to the base of the resin cement cylinders until failure. Data were analyzed using three-way ANOVA and post hoc Tukey test (α = .05).
Results: NTAP application alone (groups 3 and 4) increased SBS compared to the control group only at 24 hours. After 1 year, the NTAP/primer combination showed higher SBS than the other groups. Water storage for 1 year reduced the bond strength for all groups.
Conclusion: NTAP, combined or not combined with primer, had a beneficial effect on adhesion after 24 hours and after 1 year. Water storage negatively influenced the adhesion in all groups.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.11607/ijp.7118 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Shear bond strength and ARI scores of metal brackets to glazed glass ceramics and zirconia: an in vitro study investigating surface treatment protocols.
BMC Oral Health
December 2024
Faculty of Dentistry, Innovative Dental Materials and Interfaces Research Unit (URB2i), UR 4462, Paris Cité University, 1 rue Maurice Arnoux, Montrouge, 92120, France.
Objective: To evaluate the shear bond strength (SBS) and adhesive remnant index (ARI) scores of metal brackets to glazed lithium disilicate reinforced glass-ceramics and zirconia according to various surface treatment protocols.
Methods: A total of 240 lithium disilicate ceramic (LD) and 240 zirconia (Zr) blocks were randomly divided according to sandblasting, hydrofluoric acid (HF) etching, universal primer use, and the adhesive system applied. A maxillary canine metal bracket was bonded to each sample with resin cement (Transbond XT, TXT).
Effect of cementation technique and cement type on the amount of excess cement in implant-supported cement-retained crown restorations: An in vitro study.
J Prosthet Dent
December 2024
Professor, Department of Prosthodontics, Faculty of Dentistry, Gazi University, Ankara, Turkey.
Statement Of Problem: Excess cement in implant-supported restorations can lead to peri-implant diseases, and its removal remains a clinical challenge. The optimum method of minimizing excess cement is unclear.
Purpose: The purpose of this in vitro study was to compare 3 cementation techniques and 3 cement types and measure excess cement.
Evaluation of Shear Bond Strength of Lithium Disilicate Veneers Using Pre-heated Resin Composite With Two Conventional Resin Cements: An In Vitro Study.
Cureus
November 2024
Department of Endodontic and Operative Dentistry, Damascus University, Damascus, SYR.
Objectives This study aimed to compare the shear bond strength of three resin cements (light-cured resin cement, pre-heated composite resin, and dual-cured self-adhesive resin cement) when bonding to lithium disilicate discs. Materials and methods Thirty-six discs made of lithium disilicate were fabricated and etched with 9.5% (HF), and 36 human premolars were collected and immersed in the acrylic molds, then randomly divided into three equal groups (n = 12): Group 1: light-cured resin cement, Group 2: pre-heated resin composite, and Group 3: dual-cured resin cement.
View Article and Find Full Text PDFEvaluation of the shear bond strength of surface-treated Cobalt-Chromium metal crowns on corticobasal® implant abutments cemented using different luting agents.
J Stomatol Oral Maxillofac Surg
December 2024
Reader, Department of Periodontics, Saveetha Dental College and Hospitals, Saveetha Institute of Medical and Technical Sciences, Saveetha University, Chennai 600077, Tamil Nadu, India.. Electronic address:
Purpose: This in-vitro study aimed to compare the shear bond strength (SBS) of cobalt-chromium (Co-Cr) crowns on Corticobasal® implant abutments, evaluating the effects of two surface treatments and two luting agents.
Materials And Methods: Thirty Co-Cr crowns were fabricated using CAD-CAM technology with a direct metal laser sintering process and divided into three groups based on surface treatment: Group I (untreated), Group II (sandblasted with 50 μm Al₂O₃), and Group III (Er: YAG laser etching). Each group was further subdivided based on luting cement: Sub group A (GC Fuji Plus) and Sub group B (Rely X U200).
Trends in pH-triggered strategies for dental resins aiming to assist in preventing demineralization: A scoping review.
J Dent
December 2024
Department of Pediatric Dentistry and Orthodontics, School of Dentistry, Universidade Federal do Rio de Janeiro (UFRJ), Rodolpho Paulo Rocco, 325, Rio de Janeiro, RJ 21941-617, Brazil. Electronic address:
Objectives: To identify and map the literature on the current state of pH-triggered strategies for resin-based materials used in direct restorative dentistry, focusing on innovative compounds, their incorporation and evaluation methods, and the main outcomes.
Data And Sources: Through a search across PubMed, Scopus, Embase, Web of Science, LILACS, Cochrane Library databases, and Google Scholar, this review identified studies pertinent to pH-responsive dental materials, excluding resin-modified glass ionomer cements.
Study Selection: From the 981 records identified, 19 in vitro studies were included, concentrating on resin-based composite resins (50 %), dentin adhesives (25 %), and sealants (25 %).
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!