Stereolithography (SLA) is an additive manufacturing process based on the photocuring of resins with the use of UV light. The printed samples can be used not only for the visualization of structures, but also to develop elements of real constructions. In the study, SLA-printed samples made of Formlabs' Durable Resin were tested in static, dynamic, and Hopkinson's bar tests. The recommended UV and heat curing time for this resin is 60 min for each process. For the tests, 5-minute and 30-min curing times were also considered. The obtained stress-strain curves were compared. The resin showed a difference in response to the strain rate effect and a curing time influence was noticed. For the static tests, the post-curing time had the greatest effect with a very small standard deviation. For the dynamic tests, similar dependencies were observed but with a greater standard deviation. The tests at very high strain rates were associated with a much greater level of difficulty in execution, recording, and signal analyzing, and the influence of the exposure time on the mechanical properties was not straightforward. The tested resin showed strengthening with increases in the strain rate as well as in the curing time.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC7766486 | PMC |
| http://dx.doi.org/10.3390/ma13245825 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Rapid, Accurate and Reproducible Prediction of the Glass Transition Temperature Using Ensemble-Based Molecular Dynamics Simulation.
J Chem Theory Comput
January 2025
Centre for Computational Science, University College London, 20 Gordon Street, London WC1H 0AJ, U.K.
For the computational design of new polymeric materials, accurate methods for determining the glass transition temperature () are required. We apply an ensemble approach in molecular dynamics (MD) and examine its predictions of and their associated uncertainty. We separate the uncertainty into the aleatoric contributions arising from dynamical chaos and that due to the computational scenarios chosen to compute .
View Article and Find Full Text PDFExperimental research on resource utilization of iron tailings powder in backfilling engineering.
Sci Rep
January 2025
Detong Intelligent Technology Co., Ltd, Xuchang, 461000, China.
The goaf formed by mining and other activities is prone to safety hazards. Preparing high-quality and low-cost solidified iron tailings powder (SITP) is an important way to ensure backfill quality and eliminate safety hazards. Using iron tailings powder near the goaf of in Shanxi, comparative experiments were conducted to evaluate the the flowability, stone rate, strength, and water stability of newly mixed SITP under different types and dosages of curing agent, and mixing methods.
View Article and Find Full Text PDFDiagnostic value of 11C-Methionine PET-CT imaging in persistent or recurrent Cushing's disease after surgery.
J Clin Endocrinol Metab
January 2025
Department of Endocrinology and Nutrition, Cliniques Universitaires Saint-Luc UCL, Bruxelles, Belgium.
Introduction: Equivocal or negative pituitary magnetic resonance imaging (MRI) findings raise a significant challenge in the management of persistent or recurrent Cushing's disease (CD), compromising the chances of success of a further transsphenoidal surgery (TSS). The aim of our study was to determine the diagnostic utility of 11C-methionine (MET) positron emission tomography coupled with computerized tomography (PET/CT) in localizing the residual or relapsing corticotroph adenoma.
Methods: We retrospectively analyzed the results of 11C-MET PET/CT performed in two tertiary medical centers between May 2002 and November 2023 in 22 patients with a persisting or recurrent CD after initial TSS and equivocal or negative pituitary MRI findings.
Exploring the Internal Environmental Changes of Muscle Cells and Apoptotic Phase of Mitochondria in Dry-Cured Loin Using Electrical Stimulation: Promoting the Precise Regulation of Loin Ham Quality.
J Agric Food Chem
January 2025
Guizhou Key Laboratory of New Quality Processing and Storage of Ecological Specialty Food; School of Liquor and Food Engineering, Guizhou University, Guiyang 550025, China.
Traditional dry-curing methods have a long cycle time and low efficiency, resulting in the inconsistent quality of dry-cured ham. By applying electrical stimulation (ES) technology in the dry-curing process, it was found that ES affected mitochondrial apoptosis by modulating the intracellular environment of muscle cells, which, in turn, enhanced the quality of dry-cured pork loin. Specifically, ES accelerated glycogen and ATP depletion, which led to a rapid decline in pH.
View Article and Find Full Text PDFSingularity of Lévy walks in the lifted Pomeau-Manneville map.
Chaos
January 2025
Centre for Complex Systems, School of Mathematical Sciences, Queen Mary University of London, Mile End Road, London E1 4NS, United Kingdom.
Since groundbreaking works in the 1980s it is well-known that simple deterministic dynamical systems can display intermittent dynamics and weak chaos leading to anomalous diffusion. A paradigmatic example is the Pomeau-Manneville (PM) map which, suitably lifted onto the whole real line, was shown to generate superdiffusion that can be reproduced by stochastic Lévy walks (LWs). Here, we report that this matching only holds for parameter values of the PM map that are of Lebesgue measure zero in its two-dimensional parameter space.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!