Time Course of Recovery after Cycling Repeated Sprints.

Med Sci Sports Exerc

Post-Graduate Program in Movement Science, Laboratory of Physiology and Sport Performance (LAFIDE), São Paulo State University (UNESP), Bauru, SP, BRAZIL.

Published: February 2021

Purpose: The present study investigated the recovery of performance and neuromuscular fatigue after cycling repeated sprints.

Methods: Ten participants performed two sessions of repeated sprints (one session: 10 × 10-s sprints, 30-s recovery) separated by 24 h (R24-S1 and R24-S2) and two sessions separated by 48 h (R48-S1 and R48-S2). The recovery condition (i.e., 24 or 48 h) was randomized and separated by 1 wk. All sessions were performed on a recumbent bike, allowing minimal delay between sprints termination and neuromuscular measurements. Neuromuscular function of knee extensors (neuromuscular assessment [NMA]) was assessed before sessions (presession), after the fifth sprint (midsession), and immediately after (postsession). Before sessions, baseline NMA was also carried out on an isometric chair. The NMA (bike and chair) was composed of maximal voluntary contraction (MVC) of knee extension and peripheral neuromuscular stimulation during the MVC and on relaxed muscle.

Results: The sprints performance was not significantly different between sessions and did not presented significant interaction between recovery conditions. MVC was significantly lower at R24-S2 compared with R24-S1 (-6.5% ± 8.8%, P = 0.038) and R48-S2 (-5.6% ± 8.2%, P = 0.048), whereas resting potentiated high-frequency doublet (Db100) was lower at R24-S2 compared with R24-S1 (-10.4 ± 8.3, P = 0.01) (NMA on chair). There were significant reductions in MVC (>30%, P < 0.001) and Db100 (>38%, P < 0.001) from pre- to postsession in all sessions, without significant interactions between recovery conditions (NMA on bike).

Conclusion: Cycling repeated sprints induce significant fatigue, particularly at the peripheral level, which is fully restored after 48 h, but not 24 h, of recovery. One versus two days of recovery does not affect neuromuscular fatigue appearance during cycling repeated-sprint sessions.

Download full-text PDF

Source
http://dx.doi.org/10.1249/MSS.0000000000002482DOI Listing

Publication Analysis

Top Keywords

cycling repeated
12
repeated sprints
12
recovery
8
neuromuscular fatigue
8
sessions
8
postsession sessions
8
recovery conditions
8
lower r24-s2
8
r24-s2 compared
8
compared r24-s1
8

Similar Publications

Automatic 4D mitral valve segmentation from transesophageal echocardiography: a semi-supervised learning approach.

Med Biol Eng Comput

January 2025

Department of Electronics, Information and Bioengineering, Politecnico di Milano, Milan, Italy.

Performing automatic and standardized 4D TEE segmentation and mitral valve analysis is challenging due to the limitations of echocardiography and the scarcity of manually annotated 4D images. This work proposes a semi-supervised training strategy using pseudo labelling for MV segmentation in 4D TEE; it employs a Teacher-Student framework to ensure reliable pseudo-label generation. 120 4D TEE recordings from 60 candidates for MV repair are used.

View Article and Find Full Text PDF

Taking the titanium alloy wing-body connection joint at the rear beam of a certain type of aircraft as the research object, this study analyzed the failure mechanism and verified the structural safety of the wing-body connection joint under actual flight loads. Firstly, this study verified the validity of the loading system and the measuring system in the test system through the pre-test, and the repeatability of the test was analyzed for error to ensure the accuracy of the experimental data. Then, the test piece was subjected to 400,000 random load tests of flight takeoffs and landings, 100,000 Class A load tests, and ground-air-ground load tests, and the test piece fractured under the ground-air-ground load tests.

View Article and Find Full Text PDF

The initial investigation evaluates the feasibility of ultra high performance concrete (UHPC) as a material for reusable molds in aluminum casting. Two specific UHPC formulations were investigated: one based on ordinary Portland cement (OPC) and another utilizing alkali-activated materials (AAM). The study focused on investigating the surface through roughness measurements and the thermal durability through repeated casting cycles.

View Article and Find Full Text PDF

We have executed a cost-effective approach to produce a high-performance multifunctional human-machine interface (HMI) humidity sensor. The designed sensors were ecofriendly, flexible, and highly sensitive to variability in relative humidity (%RH) in the surroundings. In this study, we have introduced a humidity sensor by using carbon paper (as both a substrate and sensing material) and a silver (Ag) conductive ink pen.

View Article and Find Full Text PDF
Article Synopsis
  • Rapid advancements in high-performance technologies, like EV batteries and AI systems, highlight the need for better thermal management solutions due to limitations of conventional phase change materials (PCMs).
  • A new PCM made from polyethylene oxide (PEO) and lignin was developed, addressing issues like phase leakage and instability by creating a durable interlocked structure that withstands high temperatures (up to 115 °C).
  • Testing shows that these lignin-modified PEO composites effectively absorb and release heat while maintaining their shape, making them a sustainable and efficient option for advanced thermal management, especially in battery thermal management systems (BTMSs).
View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!