Precision glass molding is the most appropriate method for batch production of glass lenses with high surface accuracy and qualified optical performance. However, the form error caused by material expansion and contraction is the main factor affecting the precision of the molded lenses, thus the mold must be pre-compensated. In this paper, an effective method of mold pre-compensation based on mathematical analysis is established. Based on the thermal expansion curve of D-ZK3 glass, the freezing fictive temperature of the glass under the actual cooling rate is measured, and the mold pre-compensation factor can be quickly calculated. Experimental results show that the peak valley (PV) value of the surface form error of molded aspheric lens with an aperture of 5.3 mm is effectively reduced from 2.04 μm to 0.31 μm after the pre-compensation, thus meeting the geometric evaluation criterion.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC7760243 | PMC |
| http://dx.doi.org/10.3390/mi11121069 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Interpretable COVID-19 chest X-ray detection based on handcrafted feature analysis and sequential neural network.
Comput Biol Med
January 2025
University of Rwanda, Rwanda. Electronic address:
Deep learning methods have significantly improved medical image analysis, particularly in detecting COVID-19 chest X-rays. Nonetheless, these methodologies frequently inhibit some drawbacks, such as limited interpretability, extensive computational resources, and the need for extensive datasets. To tackle these issues, we introduced two novel algorithms: the Dynamic Co-Occurrence Grey Level Matrix (DC-GLM) and the Contextual Adaptation Multiscale Gabor Network (CAMSGNeT).
View Article and Find Full Text PDFMiniaturized inertial sensor based on high-resolution dual atom interferometry.
Rev Sci Instrum
January 2025
State Key Laboratory of Magnetic Resonance and Atomic and Molecular Physics, Innovation Academy for Precision Measurement Science and Technology, Chinese Academy of Sciences, Wuhan 430071, China.
Atom interferometry shows high sensitivity for inertial measurements in the laboratory, but it faces difficulties in field applications because of a trade-off between sensitivity and size. Therefore, there is an urgent need to develop a small sensor with high resolution for measuring acceleration and rotation in inertial navigation applications. Presented here is a miniaturized inertial sensor capable of measuring acceleration and rotation simultaneously based on high-resolution dual atom interferometers.
View Article and Find Full Text PDFBioactive Glasses: Advancing Skin Tissue Repair through Multifunctional Mechanisms and Innovations.
Biomater Res
January 2025
Department of Burn and Plastic Surgery, The First Affiliated Hospital of Soochow University, Soochow University, Suzhou 215006, China.
As a complex and dynamically regulated process, wound healing is collaboratively carried out by multiple types of cells. However, the precise mechanisms by which these cells contribute to immune regulation are not yet fully understood. Although research on bone regeneration has been quite extensive, the application of bioactive glass (BG) in skin tissue repair remains still relatively underexplored.
View Article and Find Full Text PDFA synchronized event-cue feedback loop integrating a 3D printed wearable flexible sensor-tactor platform.
Biosens Bioelectron
January 2025
Department of Physics, Virginia Commonwealth University, Richmond, VA, 23284, USA; Institute for Sustainable Energy and Environment, Virginia Commonwealth University, Richmond, VA, 23284, USA. Electronic address:
Wearable devices designed for the somatosensory system aim to provide event-cue feedback electronics and therapeutic stimulation to the peripheral nervous system. This prompts a neurological response that is relayed back to the central nervous system. Unlike virtual reality tools, these devices precisely target peripheral mechanoreceptors by administering specific stimuli.
View Article and Find Full Text PDFA new method for testing non-porous surfaces for their antimicrobial efficacy using an aerosol-generating spray chamber.
Front Microbiol
January 2025
Diagnostic and Research Institute for Hygiene, Microbiology and Environmental Medicine, Medical University of Graz, Graz, Austria.
The application of antimicrobial surfaces requires proof of their effectivity by methods in laboratories. One of the most common test methods is ISO 22196:2011, which represents a simple and inexpensive protocol by applying the bacterial suspension with known volume and concentration covered under a polyethylene film on the surfaces. The incubation is then conducted under defined humidity conditions for 24 h.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!