With the increasing application of hydraulic fracturing technology in exploration of tight oil and shale gas, the treatment of accompanying fracturing flowback fluids has become more urgent. Fe/Ni catalyst was successfully applied in the treatment of the flowback fluid for the first time in this paper. The effects of different oxidants and catalysts on the treatment of fracturing flowback were investigated. Electrolytic brine was an optimal oxidation gel breaker and molecular sieve loaded with Fe/Ni as catalyst for the treatment of fracturing flowback. Fe/Ni catalyst was characterized by SEM, EDS analysis, TEM and XRD, and the catalytic effect of the Fe/Ni proportion was explored. Fracturing flowback that dealt with catalytic oxidation was mixed with polyaluminum chloride (PAC) and polyacrylamide (PAM) for flocculation and sedimentation, through a filter, and was continuously treated for 20 days to simulate on-site operation. Finally, the suspended solids (SS) content of the fracturing flowback was steadily less than 15 mg/L, which meets the reinjection standard of fracturing flowback (SY/T 5329-2012 (China)). Hence, electrolytic brine-catalyzed oxidation treatment of high viscosity fracturing flowback possess broad application prospects.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.2166/wst.2020.496 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Review of the environmental and health risks of hydraulic fracturing fluids.
Heliyon
January 2025
Department of Civil and Environmental Engineering, Maroun Semaan Faculty of Engineering and Architecture, American University of Beirut, Lebanon.
The composition of hydraulic fracturing (HF) fluid poses risks to human health and the environment by impacting drinking water sources. Fracturing fluid recovery rate is highly variable, and the fact that a high percentage of the injected HF fluid is not produced back to the surface in some areas raises questions about its fate and possible migration into aquifers. In this paper, the composition of the HF fluid and related toxicity are described, along with insights about the environmental impact linked with HF fluid, synthesized spill data, main factors affecting the flow-back ratio, and induced seismicity related to HF activities.
View Article and Find Full Text PDFIdentification and hazard prioritization of hydrophobic organic chemicals in flowback and produced water particles: Implications for water management.
Water Res
January 2025
School of Energy and Environment and State Key Laboratory of Marine Pollution, City University of Hong Kong, Hong Kong SAR, China; Research Centre for the Oceans and Human Health, City University of Hong Kong Shenzhen Research Institute, Shenzhen 518057, China. Electronic address:
Hydraulic fracturing flowback and produced water (HF-FPW) has raised significant concerns owing to its potential impact on aquatic organisms and human health. Understanding the chemical composition of HF-FPW is crucial for developing appropriate management and remediation strategies. Herein, we performed nontarget screening on hydrophobic organic chemicals in the particulate phase of FPW (P-FPW) using gas chromatography-Orbitrap mass spectrometry coupled with cheminformatic analysis.
View Article and Find Full Text PDFPreparation and Properties of Lightweight Amphiphobic Proppant for Hydraulic Fracturing.
Polymers (Basel)
September 2024
Unconventional Petroleum Research Institute, China University of Petroleum-Beijing, Beijing 102249, China.
The wettability of the proppant is crucial in optimizing the flowback of fracturing fluids and improving the recovery of the produced hydrocarbons. Neutral wet proppants have been proven to improve the fluid flow by reducing the interaction between the fluid and the proppant surface. In this study, a lightweight amphiphobic proppant (LWAP) was prepared by coating a lightweight ceramic proppant (LWCP) with phenolic resin, epoxy resin, polytetrafluoroethylene (PTFE), and trimethoxy(1H,1H,2H,2H-heptadecafluorodecyl)silane (TMHFS) using a layer-by-layer method.
View Article and Find Full Text PDFModified guanidine gel fracturing fluid system and performance optimization for ultra-deep and ultra-high temperature oil and gas reservoirs.
Sci Rep
September 2024
College of Petroleum and Natural Gas Engineering, Liaoning Petrochemical University, Fushun, 113001, China.
The development of deep high-temperature oil and gas reservoirs gives rise to a rise in reservoir temperature along with the depth of the oil reservoir, thereby imposing higher requirements on the heat resistance of fracturing fluid. Guar gum fracturing fluid has difficulty tolerating temperatures exceeding 160 °C, thereby demanding the development of corresponding cross-linking agents, temperature stabilizers, and other additives to enhance the thermal stability of the fracturing system. Considering the distinctive characteristics of deep and ultra-deep reservoirs, such as extreme burial depth (exceeding 6000 m), ultra-high temperature (higher than 160 °C), and high fracturing pressure, an experimental modification of a guar gum fracturing fluid system was carried out, specifically tailored for ultra-high temperatures.
View Article and Find Full Text PDFStudy on Interpretation Method of Multistage Fracture Tracer Flowback Curve in Tight Oil Reservoirs.
ACS Omega
March 2024
National Key Laboratory of Deep Oil and Gas, School of Petroleum Engineering, China University of Petroleum (East China), Qingdao 266580, China.
Multistage fracturing is widely used in the development of tight oil reservoirs, and the fine description of postfracturing fracture networks is a challenge in tight oil reservoir development. Based on the formation mechanism of dual-wing fractures and the principles of tracer flowback, a mathematical model for tracer concentration in dual-wing fractures is established by considering the convective diffusion of the tracer within the fractures. An interpretation method for tracer flowback curves, utilizing a combination of Gaussian fitting and theoretical equation inversion, is developed to provide a detailed description of fracture parameters such as fracture half-length, fracture width, and fracture conductivity in the postfracturing fracture network.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!