Nanoscale light emitting diodes (nanoLEDs, diameter < 1 µm), with active and sacrificial multi-quantum well (MQW) layers epitaxially grown via metal organic chemical vapor deposition, were fabricated and released into solution using a combination of colloidal lithography and photoelectrochemical (PEC) etching of the sacrificial MQW layer. PEC etch conditions were optimized to minimize undercut roughness, and thus limit damage to the active MQW layer. NanoLED emission was blue-shifted ∼10 nm from as-grown (unpatterned) LED material, hinting at strain relaxation in the active InGaN MQW layer. X-ray diffraction also suggests that strain relaxation occurs upon nanopatterning, which likely results in less quantum confined Stark effect. Internal quantum efficiency of the lifted nanoLEDs was estimated at 29% by comparing photoluminescence at 292K and 14K. This work suggests that colloidal lithography, combined with chemical release, could be a viable route to produce solution-processable, high efficiency nanoscale light emitters.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1364/OE.403299 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Engineering of Impact Ionization Characteristics in GaAs/GaAsBi Multiple Quantum Well Avalanche Photodiodes.
ACS Photonics
November 2024
Department of Electronic and Electrical Engineering, University of Sheffield, Sheffield S1 3JD, United Kingdom.
The presence of large bismuth (Bi) atoms has been shown to increase the spin-orbit splitting energy in bulk GaAsBi, reducing the hole ionization coefficient (β) and thereby reducing the excess noise seen in avalanche photodiodes. In this study, we show that even very thin layers of GaAsBi introduced as quantum wells (QWs) in a GaAs matrix exhibit a significant reduction of β while leaving the electron ionization coefficient, α, largely unchanged. The optical and avalanche multiplication properties of a series of GaAsBi/GaAs multiple quantum well (MQW) p-i-n structures with nominally 5 nm thick, 4.
View Article and Find Full Text PDFColor-tunable micro-scale light-emitting diodes (Micro-LEDs) can achieve full-color display in a simple and low-cost way. In this paper, we demonstrate growth of three-dimensional (3D) inverted pyramid GaN on nano-patterned sapphire substrates (NPSS). By using the sputtered AlN nucleation layer, the uniformity of the inverted pyramid has been improved to a large extent.
View Article and Find Full Text PDFDeep Ultraviolet Excitation Photoluminescence Characteristics and Correlative Investigation of Al-Rich AlGaN Films on Sapphire.
Nanomaterials (Basel)
November 2024
Southern Polytechnic College of Engineering and Engineering Technology, Kennesaw State University, Marietta, GA 30060, USA.
AlGaN is attractive for fabricating deep ultraviolet (DUV) optoelectronic and electronic devices of light-emitting diodes (LEDs), photodetectors, high-electron-mobility field-effect transistors (HEMTs), etc. We investigated the quality and optical properties of AlGaN films with high Al fractions (60-87%) grown on sapphire substrates, including AlN nucleation and buffer layers, by metal-organic chemical vapor deposition (MOCVD). They were initially investigated by high-resolution X-ray diffraction (HR-XRD) and Raman scattering (RS).
View Article and Find Full Text PDFGiant Optical Anisotropy in 2D Metal-Organic Chalcogenates.
ACS Nano
September 2024
Department of Electrical and Systems Engineering, University of Pennsylvania, Philadelphia, Pennsylvania 19104, United States.
Optical anisotropy is a fundamental attribute of some crystalline materials and is quantified via birefringence. A birefringent crystal gives rise to not only asymmetrical light propagation but also attenuation along two distinct polarizations, a phenomenon called linear dichroism (LD). Two-dimensional (2D) layered materials with high in-plane and out-of-plane anisotropy have garnered interest in this regard.
View Article and Find Full Text PDFIn this paper, a 53 Gbps widely tunable transmitter is experimentally demonstrated for the first time, to our knowledge. An InGaAlAs/InP multiple-quantum-well (MQW) wafer is used with an identical layer structure for both the V-coupled cavity laser (VCL) and the electro-absorption modulator (EAM). The VCL uses a shallow-etched waveguide to reduce loss, while the EAM uses a deep-etched waveguide to increase the 3-dB modulation bandwidth.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!