Phase-change materials are chalcogenide alloys used for nonvolatile memory applications due to their rapid and reversible structural transformation. is a promising candidate that exhibits transitions dependent on thermal conductivity. The minimum lattice thermal conductivity of amorphous is investigated by surface acoustic propagation. thin films were deposited by radio frequency magnetron sputtering on (100) Si. Rutherford backscattering spectrometry and x-ray reflectivity were used to establish the elemental composition, deposition rate, and mass density. Using the Debye model, the thermal conductivity is extracted from fitted phase velocities measured by surface Brillouin scattering. The low thermal conductivity is revealed to be suitable for Joule heating.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1364/JOSAA.399149 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Defects vibrations engineering for enhancing interfacial thermal transport in polymer composites.
Sci Adv
January 2025
Department of Mechanical and Industrial Engineering, University of Massachusetts Amherst, Amherst, MA 01003, USA.
To push upper boundaries of thermal conductivity in polymer composites, understanding of thermal transport mechanisms is crucial. Despite extensive simulations, systematic experimental investigation on thermal transport in polymer composites is limited. To better understand thermal transport processes, we design polymer composites with perfect fillers (graphite) and defective fillers (graphite oxide), using polyvinyl alcohol (PVA) as a matrix model.
View Article and Find Full Text PDFOmnidirectional 3D Printing of PEDOT: PSS Aerogels with Tunable Electromechanical Performance: A Playground for Unconventional Stretchable Interconnects and Thermoelectrics.
Adv Sci (Weinh)
January 2025
Department of Materials Engineering, KU Leuven, Kasteelpark Arenberg 44, Leuven, 3001, Belgium.
The next generation of soft electronics will expand to the third dimension. This will require the integration of mechanically compliant 3D functional structures with stretchable materials. Here, omnidirectional direct ink writing (DIW) of poly(3,4-ethylenedioxythiophene): polystyrene sulfonate (PEDOT:PSS) aerogels with tunable electrical and mechanical performance is demonstrated, which can be integrated with soft substrates.
View Article and Find Full Text PDFThermoelectric properties of the low-spin lanthanide cobalate perovskites LaCoO, PrCoO, and NdCoO from first-principles calculations.
Phys Chem Chem Phys
January 2025
Department of Chemistry, University of Manchester, Oxford Road, Manchester M13 9PL, UK.
An modelling workflow is used to predict the thermoelectric properties and figure of merit of the lanthanide cobalates LaCoO, PrCoO and NdCoO in the orthorhombic phase with the low-spin magnetic configuration. The LnCoO show significantly lower lattice thermal conductivity than the widely-studied SrTiO, due to lower phonon velocities, with a large component of the heat transport through an intraband tunnelling mechanism characteristic of amorphous materials. Comparison of the calculations to experimental measurements suggests the p-type electrical properties are significantly degraded by the thermal spin crossover, and materials-engineering strategies to suppress this could yield improved .
View Article and Find Full Text PDFNon-ionic surfactant self-assembly in calcium nitrate tetrahydrate and related salts.
Soft Matter
January 2025
School of Chemistry and University of Sydney Nano Institute, The University of Sydney, Sydney, NSW, 2006, Australia.
Self-assembly of amphiphilic molecules can take place in extremely concentrated salt solutions, such as inorganic molten salt hydrates or hydrous melts. The intermolecular interactions governing the organization of amphiphilic molecules under such extreme conditions are not yet fully understood. In this study, we investigated the specific effects of ions on the self-assembly of the non-ionic surfactant CH(OCHCH)OH (CE) under extreme salt concentrations, using calcium nitrate tetrahydrate as a reference.
View Article and Find Full Text PDFGraft-to/Graft-From Synthesis of Janus Graft Copolymers for Bottlebrush Polymer Electrolytes.
Macromol Rapid Commun
January 2025
Laboratory of Material Chemistry for Energy Conversion and Storage, Ministry of Education, Hubei Key Laboratory of Material Chemistry and Service Failure, School of Chemistry and Chemical Engineering, Huazhong University of Science and Technology, Wuhan, 430074, China.
Janus graft copolymers, which combine the characteristics of block and graft copolymers, have been used in the fields of reaction catalysis, surface modification, and drug delivery, but their applications in lithium batteries have rarely been reported. Herein, Janus graft copolymers with polyethylene glycol (PEG) and polystyrene (PS) side chains are synthesized by combining reversible addition-fragmentation chain transfer (RAFT) polymerization and atom transfer radical polymerization (ATRP) methods and doped with lithium salts to fabricate Janus bottlebrush polymer electrolytes (PEG-J-PS). The PEG side chains of the brush polymers impart good ion-conducting properties to the electrolytes, while the PS side chains improve the mechanical strength and thermal and chemical stability of the electrolytes.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!