The development of stable and active TiO2 nanotubes (NTs) decorated with plasmonic gold nanoparticles (Au NPs) represents a strategy for charge-transfer processes improvements. However, organic capping ligands used for Au NPs synthesis usually remain on the surface of the metal, leading to poor Schottky junctions between Au and TiO2. Herein, we report on the synthesis of a nanotubular matrix of TiO2 decorated with gold without the need of ligands. The Au NPs mean diameter (12 nm) was similar to all the samples prepared, no matter the metal loading. Such materials enabled to use the metal as a cocatalyst for photogeneration of H2under UV and visible light irradiations. We found an optimum metal loading (2.6 wt% Au) that enabled an improvement of 760% on the H2 production when compared to the bare TiO2 NTs under UV-Vis irradiation. In addition, such catalyst was able to perform photogeneration of H2 under visible irradiation, which was not conceivable before the metal immobilization over the TiO2 NTs. The yield obtained was comparable to the observed when the catalyst was used under UV-Vis conditions. The produced materials were fully characterized by UV-Vis, XRD, TEM, and SEM.

Download full-text PDF

Source
http://dx.doi.org/10.1590/0001-3765202020200504DOI Listing

Publication Analysis

Top Keywords

tio2 nanotubes
8
visible light
8
light irradiations
8
ligands nps
8
metal loading
8
tio2 nts
8
tio2
6
metal
5
nanotubes decorated
4
decorated nanoparticles
4

Similar Publications

The current work outlines the preparation of a TiO nanotube (NT) layer electrochemically formed on the surface of a clinically-relevant titanium alloy anodisation. This NT layer was subsequently modified alternating current electrodeposition to incorporate copper micro- and nanoparticles on top of and within the NTs. Physical characterisation of the NT layer and the copper-incorporated NTs was carried out through analysis of the surface morphology, elemental composition, crystallinity, and stability SEM, EDX, XRD, and ICP-OES, respectively.

View Article and Find Full Text PDF

We present a novel approach for enhancing photocatalytic efficiency by developing polyaniline (PANI) and polyindole (PIN)-coated TiO nanotubes (TNT) through a combination of chemical oxidation and hydrothermal processes. The PANI-PIN coating was systematically applied to both the internal and external surfaces of the nanotubes to enhance the photocatalytic active sites and optimize pollutant adsorption. The dual-coated structure enhances the interaction with pollutants, facilitating a more efficient degradation of 4-nitrophenol (4-NP) when exposed to visible light.

View Article and Find Full Text PDF

Super hydrophilic and super oleophobic carbon nanotube/TiO composite membranes for efficient separation of algal-derived oil/water emulsions.

Colloids Surf B Biointerfaces

December 2024

Department of Chemical Technologies, Iranian Research Organization for Science and Technology (IROST), Tehran, Iran.

The separation of oil from microalgae aqueous emulsions is a critical step in producing algal-derived biofuels and nutraceuticals. This study presents the development of super hydrophilic and super oleophobic composite membranes to efficiently separate algal oil from oil/water emulsions. Carbon nanotubes (CNTs) were functionalized with polydopamine (PDA), polyethylene glycol (PEG), and titanium dioxide (TiO) nanoparticles and coated onto a mixed cellulose ester (MCE) substrate to fabricate the composite membranes.

View Article and Find Full Text PDF

The current study investigates and compares the biological effects of ultrathin conformal coatings of zirconium dioxide (ZrO) and vanadium pentoxide (VO) on osteoblastic MG-63 cells grown on TiO nanotube layers (TNTs). Coatings were achieved by the atomic layer deposition (ALD) technique. TNTs with average tube diameters of 15, 30, and 100 nm were fabricated on Ti substrates (via electrochemical anodization) and were used as primary substrates for the study.

View Article and Find Full Text PDF

The growing modern industry has promoted the development of gas sensors for environmental monitoring and safety checks. However, the traditional chemical resistance gas sensor still has some disadvantages such as high power consumption and limited detection, mainly due to the lack of charge transfer ability of sensing materials. In this paper, an ordered UV-activated gas sensor with mesoporous ZnO/TiO nanotube composite was prepared by precisely controlling the growth of ZnO on the inner wall of TiO nanotube.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!