Acoustic bubble dynamics in a yield-stress fluid.

Soft Matter

Department of Chemical Engineering, Imperial College London, London SW7 2AZ, UK.

Published: December 2020

Yield-stress fluids naturally trap small bubbles when their buoyancy applies an insufficient stress to induce local yielding of the material. Under acoustic excitation, trapped bubbles can be driven into volumetric oscillations and apply an additional local strain and stress that can trigger yielding and assist their release. In this paper we explore different regimes of microbubble oscillation and translation driven by an ultrasound field in a model yield-stress fluid, a Carbopol microgel. We first analyse the linear bubble oscillation dynamics to measure the local, high-frequency viscosity of the material. We then use acoustic pressure gradients to induce bubble translation and examine the elastic part of the response of the material below yielding. We find that, at moderate pressure amplitude, the additional stresses applied by volumetric oscillations and acoustic radiation forces do not lead to any detectable irreversible bubble motion. At high pressure amplitude, we observe non-spherical shape oscillations that result in erratic bubble motion. The critical pressures we observe differ from the predictions of a recent model of shape oscillations in soft solids. Based on our findings, we discuss possible reasons for the lack of bubble release in Carbopol and suggest other systems in which ultrasound-assisted bubble rise may be observed.

Download full-text PDF

Source
http://dx.doi.org/10.1039/d0sm01044hDOI Listing

Publication Analysis

Top Keywords

yield-stress fluid
8
material acoustic
8
volumetric oscillations
8
pressure amplitude
8
bubble motion
8
shape oscillations
8
bubble
6
acoustic
4
acoustic bubble
4
bubble dynamics
4

Similar Publications

Article Synopsis
  • The study investigates how enhanced oil recovery using carbon dioxide (CO) alters the properties of crude oil, specifically focusing on wax characteristics and viscosity changes.
  • As the treatment pressure increases from atmospheric levels to higher pressures (up to 25 MPa), notable changes in the composition of crude oil occur, including decreases in light hydrocarbons and increases in paraffins and wax.
  • Treatment with supercritical CO (scCO) leads to smaller wax crystal sizes and increased viscosity, with significant enhancements in gelation characteristics and wax precipitation temperatures, especially notable between pressures of 5 to 15 MPa.
View Article and Find Full Text PDF

Hypothesis: The porosity affects the rheological response of porous particle suspensions.

Experiments: Non-Brownian suspensions of porous particles immersed in a Newtonian Polyisobutene are investigated. Three different particles, with different porosity, pore structure and similar size, and non-porous irregular particles are used.

View Article and Find Full Text PDF

Soil contamination by organic and hazardous substances is a critical environmental issue, particularly in developing countries. This study investigates the limitations of double-layer theory for bentonite-organic contaminant interactions through experimental and numerical analysis. Using NaCl and KCl as salts and acetone, isopropyl alcohol, and glycerol as organic contaminants, the research explores the rheological properties of Na-bentonite dispersions.

View Article and Find Full Text PDF

Embedded 3D Printing for Microchannel Fabrication in Epoxy-Based Microfluidic Devices.

Polymers (Basel)

November 2024

State Key Laboratory of High-Performance Precision Manufacturing, School of Mechanical Engineering, Dalian University of Technology, Dalian 116024, China.

Microfluidic devices offer promising solutions for automating various biological and chemical procedures. Epoxy resin, known for its excellent mechanical properties, chemical resistance, and thermal stability, is widely used in high-performance microfluidic devices. However, the poor printability of epoxy has limited its application in 3D printing technologies for fabricating epoxy-based microfluidic devices.

View Article and Find Full Text PDF

Embedded 3D printing of engineered lung cancer model for assisting fine-needle aspiration biopsy.

Biofabrication

December 2024

Department of Mechanical Engineering, University of Nevada Reno, 1664 N Virginia St, Reno, Nevada, 89557-0705, UNITED STATES.

Lung cancer is a serious global health issue that requires the development of patient-specific, lung cancer model for surgical planning to train interventionalists and improve the accuracy of biopsies. Although the emergence of three-dimensional (3D) printing provides a promising solution to create customized models with complicated architectures, current 3D printing methods cannot accurately duplicate anatomical-level lung constructs with tumor(s) which are applicable for hands-on training and procedure planning. To address this issue, an embedded printing strategy is proposed to create respiratory bronchioles, blood vessels, and tumors in a photocurable yield-stress matrix bath.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!