Dynamic mechanics of HK-2 cell reaction to HG stimulation studied by atomic force microscopy.

Anal Methods

International Research Centre for Nano Handling and Manufacturing of China, Changchun University of Science and Technology, Changchun 130022, China. and Ministry of Education Key Laboratory for Cross-Scale Micro and Nano Manufacturing, Changchun University of Science and Technology, Changchun 130022, China and JR3CN & IRAC, University of Bedfordshire, Luton LU1 3JU, UK.

Published: November 2020

Renal tubular cell injury by exposure to high glucose (HG) stimulation mainly accounts for diabetic nephropathy (DN). To understand the mechanism of injury by HG, quantitative characterization has commonly focused on the cells that are already impaired, which ignores the signals for the process of being injured. In this study, the architecture and morphology of HK-2 cells were observed dynamically by multiple imaging methods. AFM (atomic force microscopy)-based single-cell force spectroscopy was employed to investigate the dynamic mechanics quantitatively. The results showed that the Young's modulus increased continuously from 2.44 kPa up to 4.15 kPa for the whole period of injury by HG, while the surface adhesion decreased from 2.43 nN to 1.63 nN between 12 h and 72 h. In addition, the actin filaments of HK-2 cells exposed to HG depolymerized and then nucleated with increasing Young's modulus. The absence of cell pseudopodia coincided with the reduced cell adhesion, strongly suggesting close relationships between the cell architecture, morphology and mechanical properties. Furthermore, the stages of cell reactions were identified and assessed. Overall, the dynamic mechanics of the cells facilitate the identification of injured cells and the assessment of the degree of injury for accurate diagnoses and treatments.

Download full-text PDF

Source
http://dx.doi.org/10.1039/d0ay01470bDOI Listing

Publication Analysis

Top Keywords

dynamic mechanics
12
atomic force
8
architecture morphology
8
hk-2 cells
8
young's modulus
8
cell
6
cells
5
mechanics hk-2
4
hk-2 cell
4
cell reaction
4

Similar Publications

Trees are complex and dynamic living structures, where structural stability is essential for survival and for public safety in urban environments. Tree forks, as structural junctions, are key to tree integrity but are prone to failure under stress. The specific mechanical contributions of their internal conical structures remain largely unexplored.

View Article and Find Full Text PDF

This research examines the possibility of palm oil and oil palm trunk biochar (OPTB) from pyrolysis effectively serving as alternative processing oils and fillers, substituting petroleum-based counterparts in natural rubber (NR) composites. Chemical, elemental, surface and morphological analyses were used to characterize both carbon black (CB) and OPTB, by using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) gas porosimetry, and scanning electron microscopy (SEM). The influences of OPTB contents from 0 to 100 parts per hundred rubber (phr) on thermal, dielectric, dynamic mechanical, and cure characteristics, and the key mechanical properties of particulate NR-composites were investigated.

View Article and Find Full Text PDF

Flexible Vibration Sensors with Omnidirectional Sensing Enabled by Femtosecond Laser-Assisted Fabrication.

Polymers (Basel)

January 2025

State Key Laboratory of Precision Manufacturing for Extreme Service Performance, College of Mechanical and Electrical Engineering, Central South University, Changsha 410083, China.

Vibration sensors are integral to a multitude of engineering applications, yet the development of low-cost, easily assembled devices remains a formidable challenge. This study presents a highly sensitive flexible vibration sensor, based on the piezoresistive effect, tailored for the detection of high-dynamic-range vibrations and accelerations. The sensor's design incorporates a polylactic acid (PLA) housing with cavities and spherical recesses, a polydimethylsiloxane (PDMS) membrane, and electrodes that are positioned above.

View Article and Find Full Text PDF

An original design of a simple bioreactor was used to fabricate two tubular, 200 cm long BC structures by culturing B-11267 on a molasses medium. In addition, a tubular BC-based biocomposite with improved mechanical properties was obtained by combining cultivation on the molasses medium with in situ chemical modification by polyvinyl alcohol (PVA). Moreover, the present study investigated the BC production by the B-11267 strain on the media with different molasses concentrations under agitated culture conditions.

View Article and Find Full Text PDF

In the rapidly evolving biobased materials innovation landscape, our research identifies key players and explores the evolutionary perspective of biobased innovation, offering insights into promising research areas to be further developed by biobased material scientists in search of exploiting their knowledge in novel applications. Despite the crucial role of these materials in promoting sustainable production and consumption models, systematic studies on the current innovation terrain are lacking, leaving gaps in understanding key players, emerging technologies, and market trends. To address this void, we focused on examining patents related to biobased monomers and polymers, aiming to describe the innovation strategies and business dynamics of leading assignees.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!