We report on the design, fabrication and characterization of subwavelength grating metamaterial waveguides coated with tellurium oxide. The structures are first fabricated using a standard CMOS compatible process on a silicon-on-insulator platform. Amorphous tellurium oxide top cladding material is then deposited via post-process RF magnetron sputtering. The photonic bandstructure is controlled by adjustment of the device geometry, opening a wide range of operating regimes, including subwavelength propagation, slow light and the photonic bandgap, for various wavelength bands within the 1550 nm telecommunications window. Propagation loss of 1.0 ± 0.1 dB/mm is reported for the tellurium oxide-cladded device, compared to 1.5 ± 0.1 dB/mm propagation loss reported for the silicon dioxide-cladded reference structure. This is the first time that a high-index (n > 2) oxide cladding has been demonstrated for subwavelength grating metamaterial waveguides, thus introducing a new material platform for on-chip integrated optics.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1364/OE.393729 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Talbot effect based sensor measuring grating period change in subwavelength range.
Sci Rep
December 2024
Physical Research Laboratory, Ahmedabad, Gujarat, 380009, India.
Talbot length, the distance between two consecutive self-image planes along the propagation axis for a periodic diffraction object (grating) illuminated by a plane wave, depends on the period of the object and the wavelength of illumination. This property makes the Talbot effect a straightforward technique for measuring the period of a periodic object (grating) by accurately determining the Talbot length for a given illumination wavelength. However, since the Talbot length scale is proportional to the square of the grating period, traditional Talbot techniques face challenges when dealing with smaller grating periods and minor changes in the grating period.
View Article and Find Full Text PDFInverse design (ID) is a computational method that systematically explores a design space to find optimal device geometries based on specific performance criteria. In silicon photonics, ID often generates design features that degrade significantly due to the fabrication process, limiting the applicability of these devices in scalable fabrication. We demonstrate a solution to this performance degradation through fabrication-aware inverse design (FAID), integrating lithography models for deep-ultraviolet (DUV) lithography and electron-beam lithography (EBL) into the shape optimization approach of ID.
View Article and Find Full Text PDFOblique Deposited Ultra-Thin Silver Films on Polymer Gratings for Sensitive SERS Performance.
Nanomaterials (Basel)
November 2024
Department of Electro-Optical Engineering, National Taipei University of Technology, Taipei 106, Taiwan.
A small amount of silver was obliquely deposited onto a polymer subwavelength grating to form a metasurface that comprised silver split-tubes. An ultra-thin silver film with a monitor-controlled thickness of 20 nm at the corner of each ridge of the grating provided the most sensitive surface-enhanced Raman scattering (SERS) measurements. An excitation laser beam that was incident from the substrate provided similar or better SERS enhancement than did the general configuration with the laser beam incident directly on the surface of the nanostructure.
View Article and Find Full Text PDFArticle Synopsis
- Control of transverse modes in VCSELs is crucial, and this study introduces a double heterostructure high-contrast grating (HCG) as an effective top mirror for improved control.
- The double heterostructure HCG-VCSEL is shown to suppress higher-order transverse modes, leading to better performance compared to conventional HCG-VCSELs.
- Experimental results confirm that this new design results in a reduced spectral width and a red-shifted fundamental mode, aligning well with theoretical predictions.
Article Synopsis
- Kirchhoff's law outlines the fundamental limits of thermal radiation, suggesting that breaking the principle of electromagnetic reciprocity could enhance thermal efficiency in engineering.
- A new 1D photonic crystal design, using Weyl semimetals and dielectric layers, was created to optimize nonreciprocal infrared radiation absorptance without needing additional coupling structures like gratings.
- The design process utilized genetic algorithms for global optimization and gradient ascent for local enhancement, resulting in a compact eight-layer magnetophotonic crystal that improves absorptance while reducing unwanted reciprocal light absorption.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!