Tooth shape is used to differentiate between morphologically similar species of vertebrates, including fish. This study aimed to quantify tooth shape of three sympatric species: , , and endemic to Lake Kivu, whose existing identification criteria are currently only qualitative. A quantitative tooth shape analysis was performed based on digitized tooth outline data with a subsequent elliptic Fourier analysis to test for differences among the three species. We looked at crown shape and size differences within and at geographical, habitat, and gender levels. No comparison at habitat level was done for because it is found only in littoral zone. The analysis revealed significant tooth shape differences among the three species. had a significantly longer major cusp height and a longer and larger minor cusp than that of It had also a longer major cusp height and a longer and larger minor cusp than that of . Tooth shape differences of and species were not significantly different between littoral and pelagic fish ( > .05) while differences were significant between southern and northern Lake Kivu populations ( < .05). Tooth sizes in and were significantly different, both in height and width as well as in their ratios, and this was true at sex and geographic levels ( < .05), but not at habitat level ( > .05). Tooth shape was also significantly different with sharp teeth for males compared with females of southern populations versus northern ones. These shape- and size-related differences between sexes suggest differences in the foraging strategies toward available food resources in the lake habitat. Further research should explain the genetic basis of the observed pattern.
Download full-text PDF |
Source |
---|---|
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC7319136 | PMC |
http://dx.doi.org/10.1002/ece3.6309 | DOI Listing |
Zhonghua Kou Qiang Yi Xue Za Zhi
January 2025
Clinical Division, Peking University School and Hospital of Stomatology & National Center for Stomatology & National Clinical Research Center for Oral Diseases & National Engineering Research Center of Oral Biomaterials and Digital Medical Devices & Beijing Key Laboratory of Digital Stomatology, Beijing 100034, China.
The anatomical structure of the gingival papilla around the implant is special, and it is difficult to recover after injury. The reduction of its height will have a negative impact on function and esthetics, and it is one of the many problems in implant treatment at present. This paper analyzes the influencing factors of implant gingival papilla height from three aspects: anatomical factors, implant surgical design and implant restorative design, including the classical influencing factors such as the shape of natural teeth, interproximal distance between the implant and the adjacent tooth, soft tissue grafting, and contour of implant restorations, as well as the hot and controversial influencing factors in recent years such as the thickness of soft tissues around the implant, the implant surgical timing, the flap design, and the surgical incision, in order to provide reference for clinicians in the process of implant treatment for gingival papilla preservation and reconstruction.
View Article and Find Full Text PDFPurpose: To make micro-CT comparison and evaluation of sealant penetration depth in different types of fissures after heating of the material or application of vibrations.
Materials And Methods: One hundred sound third molars have been sealed as follows: group 1 (n = 20), light-cured resin sealant at room temperature, group 2 (n = 20), light-cured resin sealant, preheated to 41.0°C, group 3 (n = 20), light-cured resin sealant, preheated to 51.
Hua Xi Kou Qiang Yi Xue Za Zhi
February 2025
Dept. of Implantology, School and Hospital of Stomatology, Cheeloo College of Medicine, Shandong University & Shandong Key Laboratory of Oral Tissue Regeneration & Shandong Engineering Research Center of Dental Materials and Oral Tissue Regeneration & Shandong Provincial Clinical Research Center for Oral Diseases, Jinan 250012, China.
Objectives: To study the clinical effect of the L-shape technique combined with concentrated growth factor on the horizontal bone defects of maxillary anterior teeth.
Methods: Twenty-five implants from 25 patients who underwent single maxillary anterior tooth implantation with simultaneous bone grafting were selected as the study subjects. Based on the bone grafting techniques, the patients were divided into a test group (L-shaped technique with guided bone regeneration combined with concentrated growth factor, 11 cases) and a control group (traditional guided bone regeneration combined with concentrated growth factor, 14 cases).
BMC Oral Health
January 2025
Faculty of Dentistry Department of Oral and Maxillofacial Radiology, Ondokuz Mayıs University, Atakum/Samsun, Turkey.
Aim: This study aimed to evaluate the prevalence, location and diameters of Posterior superior alveolar artery (PSAA) and Infraorbital foramen (IOF) to find out whether there is any relationship between PSAA and IOF, and to predict their location relative to each other in surgical procedures by using cone beam computed tomography (CBCT).
Material And Method: Bilateral maxillary sinuses were analysed retrospectively in 170 patients with no missing teeth in the maxillary posterior region. The largest locations of PSAA and IOF in the maxillary sinus were determined and their size, shape, location in relation to the teeth and distances from anatomical points were evaluated.
Sci Rep
January 2025
Department of Orthodontics, Institute of Oral Health Science, Ajou University School of Medicine, Suwon, South Korea.
Background: The demand for orthodontic treatment using clear aligners has been gradually increasing because of their superior esthetics compared with conventional fixed orthodontic therapy. This study aimed to evaluate and compare the compressive strength of three-dimensional direct printing aligners (3DPA) with that of conventional thermo-forming aligners (TFA) to determine their clinical applicability. In the experimental group, the 3DPA material TC-85 (TC-85 full) was used to create angular protrusions called rectangular pressure areas (RPA).
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!