In present work the CrC-NiCr coating was deposited on magnesium alloy substrate with high velocity oxygen fuel (HVOF) spraying. The microstructure of the samples has been characterized by means of electron microscopy, SEM and phase composition analysis carried out. The porosity of coatings has been also estimated. Finally, tests of selected mechanical properties, such as instrumented indentation, abrasive erosion have been performed. The results of the investigations confirmed that dense, homogeneous and well-adhered CrC-NiCr cermet coating is possible to obtain onto the magnesium AZ31 alloy substrate. Moreover, the coatings exhibit high resistance to erosion.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC7345897 | PMC |
| http://dx.doi.org/10.3390/ma13122775 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
The Influence of the Strain Rate on Texture Formation During the Plane Strain Compression of AZ80 Magnesium Alloy.
Materials (Basel)
December 2024
Department of Marine Design Convergence Engineering, Pukyong National University, 45 Yongso-ro, Nam-gu, Busan 48513, Republic of Korea.
Controlling microstructure and texture development is a key approach to improving the formability of magnesium alloys. In this study, the effects of the strain rate and initial texture on the texture evolution of magnesium alloys during high-temperature processing are investigated. The plane strain compression of three types of AZ80 magnesium alloys with different initial textures was assessed at 723 K and a train rate of 0.
View Article and Find Full Text PDFOptimisation of Hot-Chamber Die-Casting Process of AM60 Alloy Using Taguchi Method.
Materials (Basel)
December 2024
Faculty of Materials Engineering, Silesian University of Technology, ul. Krasińskiego 8, 40-019 Katowice, Poland.
This paper presents the effect of hot-chamber HPDC (high-pressure die casting) process parameters on the porosity, mechanical properties, and microstructure of AM60 magnesium alloy. To reduce costs, a Taguchi design of the experimental method was used to optimise the HPDC process. Six parameters set at two levels were selected for optimisation, i.
View Article and Find Full Text PDFOn the Possibility of the Deformation of Mg and Alloys Without Preheating of Initial Billets: Understanding Their Corrosion Performance via Electrochemical Tests.
Materials (Basel)
December 2024
Department of Metals and Corrosion Engineering, University of Chemistry and Technology, Technicka 5, 168 28 Prague 6, Czech Republic.
Due to limited slip systems activated at room temperature, the plastic deformation of Mg and its alloys without any preheating of initial billets is significantly limited. To overcome those issues, new methods of severe plastic deformation are discovered and developed. One such example is extrusion with an oscillating die, called KoBo.
View Article and Find Full Text PDFEffect of Sr on Mechanical Properties and Corrosion Behavior of Rolled ZM60 Alloy.
Materials (Basel)
December 2024
School of Materials Science and Engineering, Jiamusi University, Jiamusi 154000, China.
Mg-6Zn-0.5Mn as a medical magnesium alloy has good biomechanical properties and corrosion resistance, but as a fracture internal-fixation material, its strength, toughness, and corrosion resistance still need to be improved. In this paper, the element Sr, having good biocompatibility, is used as an alloy element.
View Article and Find Full Text PDFInfluence of Bonding Temperature on Microstructure and Mechanical Properties of AZ31/Zn/Sn/5083 Diffusion Joint.
Materials (Basel)
December 2024
Key Laboratory of Advanced Technologies of Materials, Ministry of Education China, School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031, China.
Diffusion bonding with an interlayer is considered an effective means of obtaining Mg/Al dissimilar alloy joints. However, at low temperatures, it is often impossible to simultaneously achieve joints between the interlayer and Mg/Al under the same bonding parameters. For this reason, the interlayer is usually prefabricated on the substrate, followed by conducting diffusion bonding.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!