This clinical report describes designing and fabricating a single-retainer resin-bonded fixed dental prosthesis with a chair-side computer-aided design/computer-aided manufacturing system. The whole procedure, from tooth extraction to final placement of the prosthesis, was completed in one day, and a single clinic visit. No clinical complications were found at the 2-year follow-up after placement of the restoration, and satisfactory functional and esthetic results were achieved.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC7239681 | PMC |
| http://dx.doi.org/10.5395/rde.2020.45.e15 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Impact of the resin cement opacity on the final color of conservative ceramic restorations and on its ability to mask substrates of different saturations.
Dent Mater
January 2025
Department of Biomaterials, School of Dentistry, University of São Paulo, Sao Paulo, Brazil.
Objective: To analyze the impact of the translucency/opacity of two commercial brands of resin cements and different translucency of lithium disilicate on the masking ability of saturated substrates.
Methods: 120 samples (n = 5) were prepared using 0.5 mm lithium disilicate (IPS e.
Effect of uniaxial bending methods on the flexural strength and Weibull analysis of heat-polymerized, CAD/CAM milled, and 3D-printed denture base resins.
Dent Mater
January 2025
Department of Oral Technology, Medical Faculty, University Hospital Bonn, Bonn, North Rhine-Westphalia, Germany; Department of Fixed Prosthodontics, Faculty of Dentistry, Suez Canal University, Ismailia, Egypt.
Objectives: To compare the flexural strength and modulus of denture base resins manufactured by conventional methods, 3-dimensional (3D) printing, and computer-aided design and computer-aided manufacturing (CAD/CAM) milling using 3-point bending (3PB) and 4-point bending (4PB) methods after simulated aging.
Methods: Ninety bars (64 ×10 ×3.3 mm) were prepared from heat-polymerized (Lucitone-199), CAD/CAM milled (G-CAM), and 3D-printed (Denturetec) denture base resins (n = 30 per material).
Importance of EQA/PT for the detection of genetic variants in comprehensive cancer genome testing.
Sci Rep
January 2025
Genetic Analysis Department, Tsukiji Registered Clinical Laboratory, Riken Genesis Co., Ltd., Tokyo, Japan.
Comprehensive genomic profiling (CGP) is increasingly used as a clinical laboratory test and being applied to cancer treatment; however, standardization and external quality assessments (EQA) have not been fully developed. This study performed cost-effective EQA and proficiency tests (PT) for CGP testing among multiple institutions those belong to the EQA working group of Japan Association for Clinical Laboratory Science (JACLS). This study revealed that preanalytical processes, such as derived nucleic acids (NA) extraction from formalin fixed paraffine embedded (FFPE) samples, are critical.
View Article and Find Full Text PDFDental arch dimensional changes in deep bite adults treated with orthodontic fixed appliances in conjunction with maxillary incisor vs. canine bite turbos during the levelling and aligning phase: a randomized clinical trial.
Clin Oral Investig
January 2025
Orthodontic Section, Department of Preventive Dentistry, Faculty of Dentistry, Prince of Songkla University, Hat Yai, Songkhla, 90112, Thailand.
Introduction: This randomized clinical trial compared arch dimensional changes, dentoskeletal changes, and the rate of overbite correction in deep bite adults treated with fixed appliances and either maxillary incisor bite turbos (IBT) or canine bite turbos (CBT).
Materials And Methods: Forty-six deep bite subjects treated with fixed appliances were randomized into IBT (n = 23) and CBT (n = 23) groups. Changes in intercanine width (ICW), arch height (AH), and Little's Irregularity Index (LII) were analyzed from before treatment (T) to 3 months after aligning with 0.
Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material.
J Vis Exp
December 2024
School of Engineering and Materials Science, Queen Mary University of London.
Article Synopsis
- The study evaluates the fracture strength of 1 mm-thick CAD/CAM occlusal veneers made from lithium disilicate (LD) and resin nanoceramics (RNC) to assess their viability in dental restoration.
- Using a novel testing protocol, the RNC group demonstrated a significantly higher load-bearing capacity compared to the LD group, indicating better durability under stress.
- Both materials experienced similar crack patterns during testing, emphasizing the importance of understanding mechanical properties for ensuring the longevity of dental restorations.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!