Simultaneous determination of strobilurin fungicides residues in bean samples by HPLC-UV-AD using boron-doped diamond electrode.

Talanta

NUPIS (Núcleo de Pesquisa em Instrumentação e Separações Analíticas), Departamento de Química, Instituto de Ciências Exatas, Universidade Federal de Juiz de Fora, 36036-900, Juiz de Fora, MG, Brazil. Electronic address:

Published: August 2020

The aim of this paper was the development of a method for the determination of six strobilurins (fungicides) using boron-doped diamond (BDD) electrode with amperometric detection (AD) homemade coupled to high performance liquid chromatography (HPLC/UV-Vis). HPLC separation of fungicides was performed in a C18 reverse phase column using both UV and AD detectors at 200 mn and 1.9 V, respectively. The linear range for each strobilurin was from 5 to 15 mg L and the correlation coefficients for all the compounds were above 0.997. Both detectors presented adequate detectability (LOD ranging from 1.33 to 1.57 μg kg) respecting the limits pre-established by regulatory agencies. The method was validated presenting good values of recovery and accuracy. In the spiked samples the recoveries ranged from 61.6% (trifloxystrobin) to 98.8% (azoxystrobin) for UV and 62.3% (trifloxystrobin) to 95.2% (azoxystrobin) for AD. In blanks spikes the recovery varied from 77.8% (picoxystrobin) to 88.4% (kresoxim-methyl) for UV and 76.7% (picoxystrobin) to 87.1% (dimoxystrobin) for AD. The method showed good precision (RSD < 10%). The results obtained by amperometric and UV detections were statistically comparable. Seven bean samples were analyzed to detect fungicide residues.

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.talanta.2020.120957DOI Listing

Publication Analysis

Top Keywords

boron-doped diamond
8
simultaneous determination
4
determination strobilurin
4
strobilurin fungicides
4
fungicides residues
4
residues bean
4
bean samples
4
samples hplc-uv-ad
4
hplc-uv-ad boron-doped
4
diamond electrode
4

Similar Publications

Understanding how to tune the properties of electroactive materials is a key parameter for their applications in energy storage systems. This work presents a comprehensive study in tailoring polyaniline (PANI) suspensions by acid-assisted polymerization method and their subsequent deposition on boron-doped diamond (BDD) supports with low/high B concentrations. The porous or densely packed morphology of PANI is successfully controlled by varying the monomer-to-initiator ratio.

View Article and Find Full Text PDF

Various electrochemical tests were carried out to elucidate the electrolytic oxidation mechanism of oxalic acid on a boron-doped diamond electrode in a nitric acid environment. These included cyclic voltammetry, AC impedance, constant current electrolysis, and electron paramagnetic resonance spectroscopy. The impact of electrode potential, current density, nitric acid concentration, and electrode plate spacing on the oxidation of oxalic acid was investigated.

View Article and Find Full Text PDF

A high-efficient electrochemical degradation of diclofenac in water on planar and microstructured 2D, and macroporous 3D boron-doped diamond electrodes: Identification of degradation and transformation products.

Chemosphere

December 2024

Comenius University in Bratislava, Faculty of Natural Sciences, Department of Analytical Chemistry, Ilkovičova 6, SK-842 15 Bratislava, Slovak Republic; University of South Bohemia in České Budějovice, Faculty of Fisheries and Protection of Waters, South Bohemian Research Center of Aquaculture and Biodiversity of Hydrocenoses, Zátiší 728/II, CZ-389 25 Vodňany, Czech Republic. Electronic address:

The highly efficient degradation of persistent organic substances by electrochemical advanced oxidation processes (EAOPs), which don't result in the formation of potentially harmful by-products, is crucial for the future of water management. In this study, boron-doped diamond electrodes (BDDE) with three morphologies (planar 2D, microstructured 2D, and macroporous 3D) were employed for the anodic oxidation of diclofenac (DCF) in two working electrolytes (NaCl and NaSO). In total, 11 by-products formed during the electrochemical oxidation of DCF were identified via HPLC-HRMS.

View Article and Find Full Text PDF

Advanced 3D-Printed Flexible Composite Electrodes of Diamond, Carbon Nanotubes, and Thermoplastic Polyurethane.

ACS Appl Polym Mater

December 2024

Department of Precision and Microsystems Engineering, Faculty of Mechanical Engineering, Delft University of Technology, Mekelweg 2, 2628 CD Delft, The Netherlands.

In this work, we pioneered the preparation of diamond-containing flexible electrodes using 3D printing technology. The herein developed procedure involves a unique integration of boron-doped diamond (BDD) microparticles and multi-walled carbon nanotubes (CNTs) within a flexible polymer, thermoplastic polyurethane (TPU). Initially, the process for the preparation of homogeneous filaments with optimal printability was addressed, leading to the development of two TPU/CNT/BDD composite electrodes with different CNT:BDD weight ratios (1:1 and 1:2), which were benchmarked against a TPU/CNT electrode.

View Article and Find Full Text PDF

The miniaturization of electrochemical supercapacitors (EC-SCs) requires electrode materials that are both durable and efficient. Boron-doped diamond (BDD) films are an ideal choice for EC-SC due to their durability and exceptional electrochemical performance. In this study, nanostructured boron-doped ultra-nanocrystalline diamonds (NBUNCD) are fabricated on Si micro-pyramids (Si) using a simple reactive ion etching (RIE) process.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!