Semiconducting single-walled carbon nanotubes (SWNTs) are potential active materials for fast-growing flexible/wearable applications with low-power dissipation, especially suitable for increasingly important radio-frequency (RF) wireless biosensor systems. However, the operation frequency of the existing flexible carbon nanotube field-effect transistors (CNT-FETs) is far below the current state-of-the-art GSM spectrum frequency band (typical 850 MHz) for near-field wireless communication applications. In this paper, we successfully conduct a 900 °C annealing process for the flexible CNT-FETs and hence significantly improve their operation frequency up to 2.1 gigahertz (GHz), making it possible to cover the current GSM spectra for integrated wireless sensor systems. The high-temperature annealing process significantly improves the electrical characteristic of the flexible CNT-FETs by removing the surfactant impurities of the SWNT materials. The obtained flexible CNT-FETs exhibit record transconductance () as high as 48 μS/μm. Despite an applied strain level of 2%, a characteristic frequency of over 1 GHz is observed. Further demonstration of GHz performance is also exhibited for flexible RF integrated circuits (ICs) such as frequency multipliers and mixers, which are the fundamental components for wireless applications. This work offers a new pathway for realizing SWNT-based wearable wireless GHz sensor systems with power efficiency.

Download full-text PDF

Source
http://dx.doi.org/10.1021/acsami.0c03810DOI Listing

Publication Analysis

Top Keywords

flexible cnt-fets
12
flexible carbon
8
carbon nanotube
8
wearable wireless
8
operation frequency
8
annealing process
8
sensor systems
8
wireless
6
frequency
5
flexible
5

Similar Publications

In this work, we propose and demonstrate a carbon nanotube (CNT) field-effect transistor (FET) based biosensor for selective detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). CNT FETs were fabricated on a flexible Kapton substrate and the sensor was fabricated by immobilizing the reverse sequence of the RNA-dependent RNA polymerase gene of SARS-CoV-2 onto the CNT channel. The biosensors were tested for the synthetic positive and control target sequences.

View Article and Find Full Text PDF

Semiconducting single-walled carbon nanotubes (SWNTs) are potential active materials for fast-growing flexible/wearable applications with low-power dissipation, especially suitable for increasingly important radio-frequency (RF) wireless biosensor systems. However, the operation frequency of the existing flexible carbon nanotube field-effect transistors (CNT-FETs) is far below the current state-of-the-art GSM spectrum frequency band (typical 850 MHz) for near-field wireless communication applications. In this paper, we successfully conduct a 900 °C annealing process for the flexible CNT-FETs and hence significantly improve their operation frequency up to 2.

View Article and Find Full Text PDF

Carbon Nanotube Complementary Gigahertz Integrated Circuits and Their Applications on Wireless Sensor Interface Systems.

ACS Nano

February 2019

Key Laboratory for the Physics and Chemistry of Nanodevices and Department of Electronics , Peking University, Beijing 100871 , China.

Along with ultralow-energy delay products and symmetric complementary polarities, carbon nanotube field-effect transistors (CNT FETs) are expected to be promising building blocks for energy-efficient computing technology. However, the work frequencies of the existing CNT-based complementary metal-oxide-semiconductor (CMOS) integrated circuits (ICs) are far below the requirement (850 MHz) in state-of-art wireless communication applications. In this work, we fabricated deep submicron CMOS FETs with considerably improved performance of n-type CNT FETs and hence significantly promoted the work frequency of CNT CMOS ICs to 1.

View Article and Find Full Text PDF

We have successfully fabricated nanometer-scale carbon nanotube field effect transistors (CNT FETs) on a flexible and transparent substrate by electron-beam lithography. The measured current-voltage data show good hole conduction FET characteristics, and the on/off ratio of the current is more than 10(2). The conductance (as well as current) systematically decreases with the increase of the strain, suggesting that the bending of the substrate still affects the deformation condition of the short channel CNT FETs.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!