Ureteropelvic junction obstruction (UPJO) is an uncommonly encountered pathology, posing a challenge for resident training. We describe the development and face validation of a robotic pyeloplasty simulation using a 3D-printed silicone-based model of UPJO for surgical training, in combination with crowdsourced scoring to objectively assess performance and learning outcomes. The organs were created using 3D modeling software and printed using a silicone-based material by Lazarus 3D, LLC. They were secured in a laparoscopic box trainer and the robotic system was docked. Eight residents and three faculty each performed two robotic-assisted right dismembered pyeloplasties on separate occaisions. Face validity was evaluated on a 5-point Likert scale. Crowd-Sourced Assessment of Technical Skills (C-SATS Inc.) scored surgical performance using the Global Evaluative Assessment of Robotic Skills (GEARS) criteria, based on video review of each simulation. All participants completed the simulation twice with fully patent anastomoses. Average time to complete the first and second trials was 44.4 min and 43.2 min, respectively. The average GEARS score was 17.1 and 17.6 for the first and second trials respectively. Participants improved on average in all 5 GEARS categories, with significant improvement in depth perception (p = 0.006). The model received mean scores (out of 5) of 4.36 for aesthetics, 4.18 for overall feel, 3.55 for realism, 4.72 for usability, and 4.72 for suturability. Residents had a significant increase in confidence between initial and final surveys on a 5-point Likert Scale: 1.63 vs. 2.38 (p = 0.03). Using 3D-printed silicone-based models, participants completed robotic-assisted dismembered pyeloplasties for training and skill acquisition. We demonstrated face validity of the simulation, which was also found to improve participant speed and significantly improve resident confidence. Crowdsourced assessment demonstrated significant improvement in depth perception.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1007/s11701-020-01072-9 | DOI Listing |
ACS Omega
December 2024
Department of Chemistry, University of Warwick, Coventry CV4 7AL, U.K.
Hydrophobic materials have been fabricated by DLP vat photopolymerization of isobornyl acrylate-based resins with chemical modification and/or surface geometry engineering. Fluorinated and polydimethylsiloxane (PDMS)-based acrylic monomers are used for chemical modification and are incorporated into the printed materials. The water wettability was significantly reduced and plateaued with as low as 5% (w/w) of the auxillary hydrophobic monomer.
View Article and Find Full Text PDFBMC Oral Health
December 2024
Department of Dental Research Cell, Dr. D. Y. Patil Dental College and Hospital, Dr. D. Y. Patil Vidyapeeth, Sant-Tukaram Nagar, Pimpri, Pune, 411018, India.
Bioinspir Biomim
October 2024
Department of Biomedical Engineering, Seoul National University College of Medicine, 103, Daehak-ro, Jongno-gu, Seoul 03080, Republic of Korea.
Soft peristaltic pumps, which use soft ring actuators instead of mechanical pistons or rollers, offer advantages in transporting liquids with non-uniform solids, such as slurry, food, and sewage. Recent advances in 3D printing with flexible thermoplastic polyurethane (TPU) present the potential for single-step fabrication of these pumps, distinguished from handcrafted, multistep traditional silicone casting methods. However, because of the relatively high hardness of TPU, TPU-based soft peristaltic pumps contract insufficiently and thus cannot perform as well as silicone-based ones.
View Article and Find Full Text PDFOtolaryngol Head Neck Surg
October 2024
Department of Otolaryngology-Head and Neck Surgery, University of California, San Diego, California, USA.
Objective: We sought to validate a laryngeal simulation model and subsequently demonstrate its efficacy in improving surgical technique.
Study Design: Pre-post interventional study.
Setting: Otolaryngology Program at a Tertiary Care Center.
BMC Oral Health
August 2024
Department of Prosthodontics, Faculty of Dentistry, Chulalongkorn University, 34 Henri-Dunant Road, Pathumwan, Bangkok, 10300, Thailand.
Background: Digitally fabricated dentures may require relining due to continual alveolar ridge resorption. However, studies evaluating the tensile bond strength (TBS) of digitally fabricated dentures bonded to denture liners are lacking. This study aimed to evaluate the TBS of autopolymerized, heat-polymerized, milled, and 3D printed denture base materials bonded to 2 acrylic-based and 2 silicone-based denture liners, both before and after thermocycling.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!